LESSON PLAN Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (11-26-2012 to 11-30 -2012) Monday 11/26 NO SCHOOL Pd. 1,7 Plastics: Pd. 2,3,6 Basic Wood : Pd. 5 Advanced Cabinetmaking: Tuesday 11/27 Pd. 1,7 Plastics: We will be adding the Pen Holders to the base when the student is completely done buffing. We will be watching a video on latex mold building. Pd. 2,3,6 Basic Wood: We will start to plane lumber down for the next project which will be the shelf. This will take approximately two class periods. Pd. 5 Advanced Cabinetmaking: Students will be working on their own projects. Some students are in the assembly stage. I will be working with these students and giving small demonstrations as needed on different methods of assembly. WEDNESDAY 11/28 Pd. 1,7 Plastics: We will be moving on to the next project which will be making of the chess set. I will be giving a demonstration on using the latex mold builder. I will be giving a demonstration on how to place the chess pieces on the sheet off metal and how they will be coating the piece with latex. Pd. 2,3,6 Basic Wood: We will continue with planning if needed. We will then start to cut boards to rough lengths so each student will perform all necessary steps to the boards as needed to prepare for the assembly of the shelf. Pd. 5 Advanced Cabinetmaking: Students will continue to work on individual projects. I will assist students as needed. Thursday 11/29 Pd. 1,7 Plastics: I will distribute so may chess pieces to each student and we will then start to follow the demonstration steps. When we are done with the mold building process each student will have a complete half set of chess piece molds that they will use twice to complete a entire chess set. Pd. 2,3,6 Basic Wood: The first board we will be making will be the top and then we will make the back board. I will give the demonstration on how students are to joint one edge of the board and then go to the table saw and cut to the correct width. And then go to the radial arm saw and cut to the correct length. Pd. 5 Advanced Cabinetmaking: Students will continue to work on individual projects. I will assist students as needed. Friday 11/30 Pd. 1,7 Plastics: Students will be working on the mold building process for the chess set. Pd. 2,3,6 Basic Wood: We will be continuing with the preparation of the of the boards needed for the assembly of the shelf. Pd. 5 Advanced Cabinetmaking: Students will continue to work on individual projects. I will assist students as needed. FOR ALL PERIODS: PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6 Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop. Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop. Assessments; Will be done by Question and Answers and Quiz.

LESSON PLAN Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (11-19-2012 to 11-23 -2012) Monday 11/19 Pd. 1,7 Plastics: Students will be buffing the pen holders. Pd. 2,3,6 Basic Wood : Students will be putting final touches to benches. Pd. 5 Advanced Cabinetmaking: Students will be working on projects. Tuesday 11/20 Pd. 1,7 Plastics: We will be adding the pen holder. We will be drilling the hole and counter sinking the head of the screw. Pd. 2,3,6 Basic Wood: Students will have benches graded and they may take them home. The cost of the bench is $6.40. Pd. 5 Advanced Cabinetmaking: Students will be working on projects. WEDNESDAY 11/21 ½ DAY Pd. 1,7 Plastics: We will be doing shop clean up with all classes. Pd. 2,3,6 Basic Wood: We will be doing shop clean up with all classes. Pd. 5 Advanced Cabinetmaking: We will be doing shop clean up with all classes. Thursday 11/22 Pd. 1,7 Plastics: Pd. 2,3,6 Basic Wood: Pd. 5 Advanced Cabinetmaking: Friday 11/23 Pd. 1,7 Plastics Pd. 2,3,6 Basic Wood: Pd. 5 Advanced Cabinetmaking: FOR ALL PERIODS: PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6 Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop. Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop. Assessments; Will be done by Question and Answers and Quiz.

LESSON PLAN Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (11-12-2012 to 11-16 -2012) Monday 11/12 Pd. 1,7 Plastics: I will be giving the buffing demonstration for the casting. We will be using two buffing machines. Again this will take at least two days to complete. I will inform students to bring some item in by Wednesday for the next project so I can evaluate the item for the project. Pd. 2,3,6 Basic Wood: I will give a demonstration on how to cut plugs and how to use them to fill screw holes and use wood putty to fill the nail holes. Students will continue the work on their projects. Pd. 5 Advanced Cabinetmaking: Students will continue to work on individual projects. I will continue to go through out the shop assisting students. Tuesday 11/13 Pd. 1,7 Plastics: Students will continue with the buffing of the paper weight project. When students are done I will grade project and they may take it home. Pd. 2,3,6 Basic Wood: I will give a demonstration on how to cut the plugs off and sanding demonstration at this time. Students will then perform the process and on Wednesday students will start to stain. Pd. 5 Advanced Cabinetmaking: Students will continue to work on individual projects. I will be going through out the shop working with students. WEDNESDAY 11/14 Pd. 1,7 Plastics: I will be giving the demonstration on the next project which will be the Penn holder project. Students must have their item to be put in the mold today. If they do not they will receive a zero for the work grade for today. Pd. 2,3,6 Basic Wood: Students will be cutting plugs off and sanding. Students will make one final check to make sure everything is done and they are ready for staining. Pd. 5 Advanced Cabinetmaking: Students will continue to work on individual projects. I will continue to go through out the shop assisting students. Thursday 11/15 Pd. 1,7 Plastics: Students will be starting the pen project. They will mix first round of resin and pour into mold they must wait till resin sets then put item in and pour the next cup of resin. Pd. 2,3,6 Basic Wood: We will be staining benches. This will take approximately two days till everyone is done. Pd. 5 Advanced Cabinetmaking: Students will continue to work on individual projects. I will continue to go through out the shop assisting students. Friday 11/16 Pd. 1,7 Plastics: Students will be continuing to pour the mold if they did not get to on Thursday and students that did pour on Thursday will start to Sand. Pd. 2,3,6 Basic Wood: Students will continue to stain benches. We will allow benches to dry over the week end. Pd. 5 Advanced Cabinetmaking: Students will continue to work on individual projects. I will continue to go through out the shop assisting students. FOR ALL PERIODS: PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6 Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop. Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop. Assessments; Will be done by Question and Answers and Quiz.

LESSON PLAN Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (11-5-2012 to 11-9 -2012) Monday 11/5 Pd. 1,7 Plastics: Students will be working on Cast Paper Weight project. They must have some sort of flat object or picture that can be put into the mold. Pd. 2,3,6 Basic Wood: Students will be taking the safety quiz on the Power Miter Saw. After the quiz they will be working on projects. Pd. 5 Advanced Cabinetmaking: Students will continue to work on individual projects. I will continue to go through out the shop assisting students. Tuesday 11/6 Pd. 1,7 Plastics: Students that have poured their molds on Monday will be taking them out of the molds so that the rest of the students could pour their molds. Pd. 2,3,6 Basic Wood: Students will be finishing sanding and routering. They will be double checking to make sure that evey thing is ready for assembly. Pd. 5 Advanced Cabinetmaking: I will be checking on progress of each student. I will be checking measurements of boards to make sure they are correct and they are following instructions correctly so that wood is not cut inaccurately. WENDNESDAY 11/7 Pd. 1,7 Plastics: I will be giving the demonstration on sanding the casting down. They will first be shown how to use the disc sander and then to the hand sanders. Pd. 2,3,6 Basic Wood: I will be giving a demonstration on assembly. This will be done using a jig that we will be placing the parts into so that all parts are positioned correctly. We will be using air brads to hold parts to gether and then using screws for maximum strength. Pd. 5 Advanced Cabinetmaking: Students will continue to work on individual projects. I will continue to go through out the shop assisting students. Thursday 11/8 Pd. 1,7 Plastics: Students will be continuing the sanding process on their castings. This will take at lest two days. We must use a series of different grit sad paper so to achieve the smoothest finish. Pd. 2,3,6 Basic Wood: Students will be continuing with assembly. This will take at least two days till all students are done with this part of the project. I will be demonstrating the cutting of the plugs and the final sanding. Pd. 5 Advanced Cabinetmaking: Students will continue to work on individual projects. I will continue to go through out the shop assisting students. Friday 11/9 Pd. 1,7 Plastics: I will be giving the buffing demonstration for the casting. We will be using two buffing machines. Again this will take at least two days to complete. Pd. 2,3,6 Basic Wood: Students will continue the work on their projects. Pd. 5 Advanced Cabinetmaking: Students will continue to work on individual projects. I will continue to go through out the shop assisting students. FOR ALL PERIODS: PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6 Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop. Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop. Assessments; Will be done by Question and Answers and Quiz.