LESSON PLAN
Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (12/19/2011 to 12/23/2011)
Monday 12/19
Pd. 1,4,7 Basic Wood: We will start to plan wood down to proper size for the clock project. We will be using Red oak. It will take approximately 2 board feet per students.
Pd. 5 Advanced Cabinetmaking: Three students will be finished assembling their coffee tables and they will start to stain. We will be assembling the main case work for one student’s book case.
Pd. 2,3 Plastics Technology: I will give a demonstration on using the engraver to make the small name plate and attaching the clip pin to the back.
Tuesday 12/20
Pd. 1,4,7 Basic Wood: I will be giving a demonstration on cutting of the individual pieces for the clock. There will be a total of six different pieces of wood for the entire clock. This will take approximately two days till all students will have all pieces cut.
Pd. 5 Advanced Cabinetmaking: Students will continue working on individual projects. They will Two students will be cutting parts for door. I will be giving a demonstration on using the shaper table. This machine will only be used by the instructor do to the safety factors. This machine takes considerable experience to safely operate.
Pd. 2,3 Plastics Technology: Students will continue to work on the small name plate project. Some students will start to work the chess set project. They will be attaching the chess pieces to the metal plate and then they will be coating with latex.
WENDNESDAY 12/21
Pd. 1,4,7 Basic Wood: Students will continue to cut pieces of wood out for the clock project.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on individual projects.
Pd. 2,3 Plastics Technology: Students in the 2nd pd. will be removing their chess pieces from the latex molds. This will require the use of baby powder so that the latex does not stick to itself. I will be giving this demonstration first then students will do it. Students in the 3rd pd. will continue with the chess set project.
Thursday 12/22
Pd. 1,4,7 Basic Wood: We will be doing a complete cleaning and reorganizing of the wood shop before the holiday season. Power equipment must be cleaned and all hand tools cleaned and reorganized.
Pd. 5 Advanced Cabinetmaking: Same as 1st pd.
Pd. 2,3 Plastics Technology: Students will put one coat of latex on chess pieces and then we will do cleanup work .
Friday 12/23
Pd. 1,4,7 Basic Wood: Watch safety videos during shot class time periods.
Pd. 5 Advanced Cabinetmaking: Watch safety videos during shot class time periods.
Pd. 2,3 Plastics Technology: Watch safety videos during shot class time periods.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6,
Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Assessments; Will be done by Question and Answers and Quiz.
Wednesday, December 21, 2011
Monday, December 12, 2011
LESSON PLAN
Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (12/12/2011 to 12/16/2011)
Monday 12/12
Pd. 1,4,7 Basic Wood: I will give a demonstration on staining their shelf project. Students will then proceed to stain their shelves. They may choose the color of stain that they prefer. Students must following all instructions and steps as given in order to achieve a good finish.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on individual projects. We will be assembling the coffee table projects today. Two students will be applying molding to the lower base cabinet of their gun cabinets. We will use the dado cutters on two other students Cabinets so we can start to assemble them.
Pd. 2,3 Plastics Technology: Period 2 will be starting the Chess set project. I will be giving a demonstration on coating the chess pieces with latex mold builder. Period 3 will be finishing up the pen holder project.
Tuesday 12/13
Pd. 1,4,7 Basic Wood: Students will continue to stain their shelves and students who have finished staining the day before will be clear coating.
Pd. 5 Advanced Cabinetmaking: Students will continue with individual projects and I will provide assistance as needed. Some students do need more assistance then others and I will be spending more time with these students.
Pd. 2,3 Plastics Technology: 2nd period will continue with coating of pieces. The 3rd period class will be given the demonstration on coating the chess pieces for the chess project.
WENDNESDAY 12/14
Pd. 1,4,7 Basic Wood: Students will continue with staining and clear coating of shelves.
Pd. 5 Advanced Cabinetmaking: Will give a demonstration on Staining. Three students will be staining their projects. Others will continue to work on projects.
Pd. 2,3 Plastics Technology: Bothe class will continue with coating of chess piece. Each student will receive a complete chess set to coat. We will be applying three coats to the chess set.
Thursday 12/15
Pd. 1,4,7 Basic Wood: Most students will be done staining and clear coating their first coat I will give a demonstration on sanding the first coat and stress to the students the importance of removing any dirt from the finish and how to properly wipe it down be for starting the third coat.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on individual projects. Students who stained the day before will start to do there clear coating. They will be using and indoor/outdoor clear coat so that anything that is wet like a glass will not damage the finish.
Pd. 2,3 Plastics Technology: Students will be coating chess pieces. Some students will be finishing the pen holder project.
Friday 12/16
Pd. 1,4,7 Basic Wood: Students will be applying last coat of clear coat. We will then start to plane lumber down for the clock project. We will be using Red Oak.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on individual projects.
Pd. 2,3 Plastics Technology: I will be giving a demonstration on using the Plastic Engraving Machine this will take approximately 20 minutes. When we are done some students will proceed to coat chess pieces and other students will start to do their engraving project. Students will be doing their names on the engraver. They will be aloud to chose from a variety of colors.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6,
Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Assessments; Will be done by Question and Answers and Quiz.
Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (12/12/2011 to 12/16/2011)
Monday 12/12
Pd. 1,4,7 Basic Wood: I will give a demonstration on staining their shelf project. Students will then proceed to stain their shelves. They may choose the color of stain that they prefer. Students must following all instructions and steps as given in order to achieve a good finish.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on individual projects. We will be assembling the coffee table projects today. Two students will be applying molding to the lower base cabinet of their gun cabinets. We will use the dado cutters on two other students Cabinets so we can start to assemble them.
Pd. 2,3 Plastics Technology: Period 2 will be starting the Chess set project. I will be giving a demonstration on coating the chess pieces with latex mold builder. Period 3 will be finishing up the pen holder project.
Tuesday 12/13
Pd. 1,4,7 Basic Wood: Students will continue to stain their shelves and students who have finished staining the day before will be clear coating.
Pd. 5 Advanced Cabinetmaking: Students will continue with individual projects and I will provide assistance as needed. Some students do need more assistance then others and I will be spending more time with these students.
Pd. 2,3 Plastics Technology: 2nd period will continue with coating of pieces. The 3rd period class will be given the demonstration on coating the chess pieces for the chess project.
WENDNESDAY 12/14
Pd. 1,4,7 Basic Wood: Students will continue with staining and clear coating of shelves.
Pd. 5 Advanced Cabinetmaking: Will give a demonstration on Staining. Three students will be staining their projects. Others will continue to work on projects.
Pd. 2,3 Plastics Technology: Bothe class will continue with coating of chess piece. Each student will receive a complete chess set to coat. We will be applying three coats to the chess set.
Thursday 12/15
Pd. 1,4,7 Basic Wood: Most students will be done staining and clear coating their first coat I will give a demonstration on sanding the first coat and stress to the students the importance of removing any dirt from the finish and how to properly wipe it down be for starting the third coat.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on individual projects. Students who stained the day before will start to do there clear coating. They will be using and indoor/outdoor clear coat so that anything that is wet like a glass will not damage the finish.
Pd. 2,3 Plastics Technology: Students will be coating chess pieces. Some students will be finishing the pen holder project.
Friday 12/16
Pd. 1,4,7 Basic Wood: Students will be applying last coat of clear coat. We will then start to plane lumber down for the clock project. We will be using Red Oak.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on individual projects.
Pd. 2,3 Plastics Technology: I will be giving a demonstration on using the Plastic Engraving Machine this will take approximately 20 minutes. When we are done some students will proceed to coat chess pieces and other students will start to do their engraving project. Students will be doing their names on the engraver. They will be aloud to chose from a variety of colors.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6,
Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Assessments; Will be done by Question and Answers and Quiz.
Monday, December 5, 2011
LESSON PLAN
Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (12/7/2011 to 12/9/2011)
Monday 12/5
Pd. 1,4,7 Basic Wood: Students will be working on shelf projects. We will be sanding all parts and routering the edges that need to be routed.
Pd. 5 Advanced Cabinetmaking: Students will be working on individual projects. I will be giving a demonstration on using the chisel.
Pd. 2,3 Plastics Technology: Students will be working on the pen holder projects. They must have some item that can be laid flat inside the mold.
Tuesday 12/6
Pd. 1,4,7 Basic Wood: Students will be working on projects.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on individual projects.
Pd. 2,3 Plastics Technology: Students will continue to work on acrylic pen holder projects.
WENDNESDAY 12/7
Pd. 1,4,7 Basic Wood: I will be giving a demonstration on assembling projects. Students will be using the air nail gun and glue to assemble. I will be working with each student during this process.
Pd. 5 Advanced Cabinetmaking: Students will continue to assemble projects.
Pd. 2,3 Plastics Technology: Students will continue to work on acrylic pen holders. They must follow all steps correctly in order for project to be finished correctly.
Thursday 12/8
Pd. 1,4,7 Basic Wood: We will continue to assemble shelf projects .
Pd. 5 Advanced Cabinetmaking: Students will continue to work on projects.
Pd. 2,3 Plastics Technology: Students should have all poured there projects by today. Most students will be sanding and buffing.
Friday 12/9
Pd. 1,4,7 Basic Wood: Students will continue to cut their project pieces to proper sizes.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on projects.
Pd. 2,3 Plastics Technology: I will be giving a demonstration on drilling the hole for the pen base. Students will be doing this on the Drill press this will be a two step process. They will then add the pen holder. They must put piece of tape on the back with their name on and hand it in for a grade.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Assessments; Will be done by Question and Answers and Quiz.
Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (12/7/2011 to 12/9/2011)
Monday 12/5
Pd. 1,4,7 Basic Wood: Students will be working on shelf projects. We will be sanding all parts and routering the edges that need to be routed.
Pd. 5 Advanced Cabinetmaking: Students will be working on individual projects. I will be giving a demonstration on using the chisel.
Pd. 2,3 Plastics Technology: Students will be working on the pen holder projects. They must have some item that can be laid flat inside the mold.
Tuesday 12/6
Pd. 1,4,7 Basic Wood: Students will be working on projects.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on individual projects.
Pd. 2,3 Plastics Technology: Students will continue to work on acrylic pen holder projects.
WENDNESDAY 12/7
Pd. 1,4,7 Basic Wood: I will be giving a demonstration on assembling projects. Students will be using the air nail gun and glue to assemble. I will be working with each student during this process.
Pd. 5 Advanced Cabinetmaking: Students will continue to assemble projects.
Pd. 2,3 Plastics Technology: Students will continue to work on acrylic pen holders. They must follow all steps correctly in order for project to be finished correctly.
Thursday 12/8
Pd. 1,4,7 Basic Wood: We will continue to assemble shelf projects .
Pd. 5 Advanced Cabinetmaking: Students will continue to work on projects.
Pd. 2,3 Plastics Technology: Students should have all poured there projects by today. Most students will be sanding and buffing.
Friday 12/9
Pd. 1,4,7 Basic Wood: Students will continue to cut their project pieces to proper sizes.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on projects.
Pd. 2,3 Plastics Technology: I will be giving a demonstration on drilling the hole for the pen base. Students will be doing this on the Drill press this will be a two step process. They will then add the pen holder. They must put piece of tape on the back with their name on and hand it in for a grade.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Assessments; Will be done by Question and Answers and Quiz.
Tuesday, November 29, 2011
LESSON PLAN
Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (11/28/2011 to 12/2/2011)
Monday 11/29 NO SCHOOL
Pd. 1,4,7 Basic Wood:
Pd. 5 Advanced Cabinetmaking:
Pd. 2,3 Plastics Technology:
Tuesday 11/30
Pd. 1,4,7 Basic Wood: We will be starting our next project. Students will be planning lumber down to size for the shelf. The shelf will be made of white pine. Some students will be finishing up their bench projects.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on individual projects and I will give a demonstration on gluing and assembling of the dove tail chest that a student is building.
Pd. 2,3 Plastics Technology: Students will continue to work on acrylic paper pour projects.
WENDNESDAY 11/30
Pd. 1,4,7 Basic Wood: We will continue with the planning of lumber and we will then start to cut to rough lengths so that each student will have their own pieces of wood.
Pd. 5 Advanced Cabinetmaking: Students will continue to assemble projects. I will be working with two students to assemble coffee tables.
Pd. 2,3 Plastics Technology: Students will continue to work on acrylic paper pour projects.
Thursday 12/1
Pd. 1,4,7 Basic Wood: I will give a review demonstration on the process of cutting the boards to the proper widths and to the finished lengths.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on projects.
Pd. 2,3 Plastics Technology: Students will continue to work on acrylic paper pour projects.
Friday 12/2
Pd. 1,4,7 Basic Wood: Students will continue to cut their project pieces to proper sizes.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on projects.
Pd. 2,3 Plastics Technology: Students will be finishing their 1st acrylic pour project. I will be giving a demonstration on the next project which will be the Pen holder.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Assessments; Will be done by Question and Answers and Quiz.
Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (11/28/2011 to 12/2/2011)
Monday 11/29 NO SCHOOL
Pd. 1,4,7 Basic Wood:
Pd. 5 Advanced Cabinetmaking:
Pd. 2,3 Plastics Technology:
Tuesday 11/30
Pd. 1,4,7 Basic Wood: We will be starting our next project. Students will be planning lumber down to size for the shelf. The shelf will be made of white pine. Some students will be finishing up their bench projects.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on individual projects and I will give a demonstration on gluing and assembling of the dove tail chest that a student is building.
Pd. 2,3 Plastics Technology: Students will continue to work on acrylic paper pour projects.
WENDNESDAY 11/30
Pd. 1,4,7 Basic Wood: We will continue with the planning of lumber and we will then start to cut to rough lengths so that each student will have their own pieces of wood.
Pd. 5 Advanced Cabinetmaking: Students will continue to assemble projects. I will be working with two students to assemble coffee tables.
Pd. 2,3 Plastics Technology: Students will continue to work on acrylic paper pour projects.
Thursday 12/1
Pd. 1,4,7 Basic Wood: I will give a review demonstration on the process of cutting the boards to the proper widths and to the finished lengths.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on projects.
Pd. 2,3 Plastics Technology: Students will continue to work on acrylic paper pour projects.
Friday 12/2
Pd. 1,4,7 Basic Wood: Students will continue to cut their project pieces to proper sizes.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on projects.
Pd. 2,3 Plastics Technology: Students will be finishing their 1st acrylic pour project. I will be giving a demonstration on the next project which will be the Pen holder.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Assessments; Will be done by Question and Answers and Quiz.
Monday, November 21, 2011
LESSON PLAN
Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (11/21/2011 to 11/25/2011)
Monday 11/21
Pd. 1,4,7 Basic Wood: Students will be clear coating benches. They will be able to put second and third coats on and take them home Tuesday.
Pd. 5 Advanced Cabinetmaking: Students will be working on projects. Some students will be assembling. I will demonstrate assembling the dove tail chest.
Pd. 2,3 Plastics Technology: We will be pouring the acrylic projects. Some students will be sanding and then start to buff.
Tuesday 11/22
Pd. 1,4,7 Basic Wood: Students will continue with clear coating. Some students will be taking the benches home after grading.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on projects.
Pd. 2,3 Plastics Technology: Students will continue with the acrylic project.
WENDNESDAY 11/23 1 /2 DAY Clean UP DAY
Pd. 1,4,7 Basic Wood: CLEAN THE SHOP
Pd. 5 Advanced Cabinetmaking: CLEAN THE SHOP
Pd. 2,3 Plastics Technology: CLEAN THE SHOP
Thursday 11/24 NO SCHOOL
Pd. 1,4,7 Basic Wood:
Pd. 5 Advanced Cabinetmaking:
Pd. 2,3 Plastics Technology: Students
Friday 11/25 NO SCHOOL
Pd. 1,4,7 Basic Wood:
Pd. 5 Advanced Cabinetmaking:
Pd. 2,3 Plastics Technology:
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Assessments; Will be done by Question and Answers and Quiz.
Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (11/21/2011 to 11/25/2011)
Monday 11/21
Pd. 1,4,7 Basic Wood: Students will be clear coating benches. They will be able to put second and third coats on and take them home Tuesday.
Pd. 5 Advanced Cabinetmaking: Students will be working on projects. Some students will be assembling. I will demonstrate assembling the dove tail chest.
Pd. 2,3 Plastics Technology: We will be pouring the acrylic projects. Some students will be sanding and then start to buff.
Tuesday 11/22
Pd. 1,4,7 Basic Wood: Students will continue with clear coating. Some students will be taking the benches home after grading.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on projects.
Pd. 2,3 Plastics Technology: Students will continue with the acrylic project.
WENDNESDAY 11/23 1 /2 DAY Clean UP DAY
Pd. 1,4,7 Basic Wood: CLEAN THE SHOP
Pd. 5 Advanced Cabinetmaking: CLEAN THE SHOP
Pd. 2,3 Plastics Technology: CLEAN THE SHOP
Thursday 11/24 NO SCHOOL
Pd. 1,4,7 Basic Wood:
Pd. 5 Advanced Cabinetmaking:
Pd. 2,3 Plastics Technology: Students
Friday 11/25 NO SCHOOL
Pd. 1,4,7 Basic Wood:
Pd. 5 Advanced Cabinetmaking:
Pd. 2,3 Plastics Technology:
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Assessments; Will be done by Question and Answers and Quiz.
Tuesday, November 15, 2011
LESSON PLAN
Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (11/14/2011 to 11/18/2011)
Monday 11/14
Pd. 1,4,7 Basic Wood: I will be giving a demonstration on assembling the stool. We will be using the air nail gun and the electric drills.
Pd. 5 Advanced Cabinetmaking: I will be giving a demonstration on using the Dove Tail Jigs This will take most of the time of class. If any time is left students will be able to work.
Pd. 2,3 Plastics Technology: Students will be finishing up any buffing to be done on the mugs. We will finish applying the handles to the mugs.
Tuesday 11/15
Pd. 1,4,7 Basic Wood: We will be assembling Benches. I will be giving a demonstration cutting plugs and filling the nail holes and screw holes.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on projects.
Pd. 2,3 Plastics Technology: I will be giving a demonstration on cutting out stencils to apply to the mugs and the use of the sand blaster. Students will be adding designs to the mugs.
WENDNESDAY 11/16
Pd. 1,4,7 Basic Wood: Students will continue to assemble benches and fill holes. I will be giving a demonstration on using the plug cutting saw and how to sand the plugs down.
Pd. 5 Advanced Cabinetmaking: Some students will be assembling some parts of their projects. They will continue to work on projects.
Pd. 2,3 Plastics Technology: We will continue with the adding of designs to the mugs.
Thursday 11/17
Pd. 1,4,7 Basic Wood: Students will continue to work on benches.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on projects. I will give a demonstration on assembling the Blanket chest that we cut dove tails into. This will take a sometime and help will be required by other students.
Pd. 2,3 Plastics Technology: Students will be finishing the Sand blasting process.
Friday 11/18
Pd. 1,4,7 Basic Wood: I will be giving a demonstration on Staining benches and students will start to stain.
Pd. 5 Advanced Cabinetmaking: I will be giving a demonstration on using the biscuit cutter to put three students’ table tops together.
Pd. 2,3 Plastics Technology: I will be giving a demonstration on the next project which will be Pouring of resin to make the paper weight.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Assessments; Will be done by Question and Answers and Quiz.
Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (11/14/2011 to 11/18/2011)
Monday 11/14
Pd. 1,4,7 Basic Wood: I will be giving a demonstration on assembling the stool. We will be using the air nail gun and the electric drills.
Pd. 5 Advanced Cabinetmaking: I will be giving a demonstration on using the Dove Tail Jigs This will take most of the time of class. If any time is left students will be able to work.
Pd. 2,3 Plastics Technology: Students will be finishing up any buffing to be done on the mugs. We will finish applying the handles to the mugs.
Tuesday 11/15
Pd. 1,4,7 Basic Wood: We will be assembling Benches. I will be giving a demonstration cutting plugs and filling the nail holes and screw holes.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on projects.
Pd. 2,3 Plastics Technology: I will be giving a demonstration on cutting out stencils to apply to the mugs and the use of the sand blaster. Students will be adding designs to the mugs.
WENDNESDAY 11/16
Pd. 1,4,7 Basic Wood: Students will continue to assemble benches and fill holes. I will be giving a demonstration on using the plug cutting saw and how to sand the plugs down.
Pd. 5 Advanced Cabinetmaking: Some students will be assembling some parts of their projects. They will continue to work on projects.
Pd. 2,3 Plastics Technology: We will continue with the adding of designs to the mugs.
Thursday 11/17
Pd. 1,4,7 Basic Wood: Students will continue to work on benches.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on projects. I will give a demonstration on assembling the Blanket chest that we cut dove tails into. This will take a sometime and help will be required by other students.
Pd. 2,3 Plastics Technology: Students will be finishing the Sand blasting process.
Friday 11/18
Pd. 1,4,7 Basic Wood: I will be giving a demonstration on Staining benches and students will start to stain.
Pd. 5 Advanced Cabinetmaking: I will be giving a demonstration on using the biscuit cutter to put three students’ table tops together.
Pd. 2,3 Plastics Technology: I will be giving a demonstration on the next project which will be Pouring of resin to make the paper weight.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Assessments; Will be done by Question and Answers and Quiz.
Monday, November 7, 2011
LESSON PLAN
Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (11/7/2011 to 11/11/2011)
Monday 11/7
Pd. 1,4,7 Basic Wood: Students will continue the sanding of the project pieces and cutting the angle on the middle brace piece.
Pd. 5 Advanced Cabinetmaking: I will be giving a demonstration on using the Dado blades on the tale saw to cut Dado joints in two students project pieces.
Pd. 2,3 Plastics Technology: I will be giving the demonstration on getting The Mug project started. We will be cutting a piece of clear acrylic for the bottom of the mug. I will be give demonstration on how to glue it in position.
Tuesday 11/8
Pd. 1,4,7 Basic Wood: We will start to plan lumber down to make the top of the benches. We will be gluing the boards together to achieve the proper width.
Pd. 5 Advanced Cabinetmaking: Students will be working on projects. I will be giving a demonstration on assembling the lower cabinet of a gun cabinet.
Pd. 2,3 Plastics Technology: Students will be working on glue it in position if they did not get to it on Monday. I will be giving a demonstration on how to sand the edges of the bottom down to the proper side and how to use the hand sanders.
WENDNESDAY 11/9
Pd. 1,4,7 Basic Wood: I will be giving a demonstration on gluing the boards together for the proper width. We will then start to glue. All students will be helping with this so they have a full understanding of the process.
Pd. 5 Advanced Cabinetmaking: I will be giving a demonstration on using the Dove tail cutters. We will be using them on a large blanket chest.
Pd. 2,3 Plastics Technology: Students will be sanding the bottom to proper size. I will give demonstration on buffing it to finish the bottom. Students will be receiving the acrylic rod for the handle.
Thursday 11/10
Pd. 1,4,7 Basic Wood: We will be cutting boards to a rough measurement and then each student will be planning their own board done to the proper thickness of ¾”. They will then run the board through the jointer and then the table saw to achieve the proper width. They will then cut to the proper length and make sure it is square.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on projects
Pd. 2,3 Plastics Technology: Students will be finishing the sanding and the buffing of the bottom of the mug.
Friday 11/11 No School for Students Act 80 Day In Service
Pd. 1,4,7 Basic Wood:
Pd. 5 Advanced Cabinetmaking:
Pd. 2,3 Plastics Technology:
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Assessments; Will be done by Question and Answers and Quiz.
Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (11/7/2011 to 11/11/2011)
Monday 11/7
Pd. 1,4,7 Basic Wood: Students will continue the sanding of the project pieces and cutting the angle on the middle brace piece.
Pd. 5 Advanced Cabinetmaking: I will be giving a demonstration on using the Dado blades on the tale saw to cut Dado joints in two students project pieces.
Pd. 2,3 Plastics Technology: I will be giving the demonstration on getting The Mug project started. We will be cutting a piece of clear acrylic for the bottom of the mug. I will be give demonstration on how to glue it in position.
Tuesday 11/8
Pd. 1,4,7 Basic Wood: We will start to plan lumber down to make the top of the benches. We will be gluing the boards together to achieve the proper width.
Pd. 5 Advanced Cabinetmaking: Students will be working on projects. I will be giving a demonstration on assembling the lower cabinet of a gun cabinet.
Pd. 2,3 Plastics Technology: Students will be working on glue it in position if they did not get to it on Monday. I will be giving a demonstration on how to sand the edges of the bottom down to the proper side and how to use the hand sanders.
WENDNESDAY 11/9
Pd. 1,4,7 Basic Wood: I will be giving a demonstration on gluing the boards together for the proper width. We will then start to glue. All students will be helping with this so they have a full understanding of the process.
Pd. 5 Advanced Cabinetmaking: I will be giving a demonstration on using the Dove tail cutters. We will be using them on a large blanket chest.
Pd. 2,3 Plastics Technology: Students will be sanding the bottom to proper size. I will give demonstration on buffing it to finish the bottom. Students will be receiving the acrylic rod for the handle.
Thursday 11/10
Pd. 1,4,7 Basic Wood: We will be cutting boards to a rough measurement and then each student will be planning their own board done to the proper thickness of ¾”. They will then run the board through the jointer and then the table saw to achieve the proper width. They will then cut to the proper length and make sure it is square.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on projects
Pd. 2,3 Plastics Technology: Students will be finishing the sanding and the buffing of the bottom of the mug.
Friday 11/11 No School for Students Act 80 Day In Service
Pd. 1,4,7 Basic Wood:
Pd. 5 Advanced Cabinetmaking:
Pd. 2,3 Plastics Technology:
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Assessments; Will be done by Question and Answers and Quiz.
Monday, October 31, 2011
LESSON PLAN
Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (10/31/2011 to 11/4/2011)
Monday 10/31 *Due to repairs on a pipe in the wood shop we will be out of the shop on Monday or Tuesday. We will be over in the Power Tech room or the Health Room*
Pd. 1,4,7 Basic Wood: I will be giving a demonstration on Laying out of the angles to be cut on the bench ends. They will also be tracing the radius on the bottom edge of pieces. I will then give a demonstration on using the Band saw to cut the project pieces out. We will be using three different Band Saws. Students may choose which one they are more comfortable using.
Pd. 5 Advanced Cabinetmaking: I will give a demonstration using the Power Miter Saw to the advanced class and the test will be given the following Day.
Pd. 2,3 Plastics Technology: Students will continue with the desk organizer project. They will be gluing together. After 24 hours they will be sanding using three different grits of sand paper.
Tuesday 11/1
Pd. 1,4,7 Basic Wood: Students will continue to cut project pieces out.
Pd. 5 Advanced Cabinetmaking: Test will be given on the power miter saw. Students will continue to work on individual projects. As students get to different processes with project part construction I will be give group demonstrations’.
Pd. 2,3 Plastics Technology: I will give a demonstration on buffing the project. There is a specific order to follow in buffing this project.
WENDNESDAY 11/2
Pd. 1,4,7 Basic Wood: Students will continue to cut project pieces out. I will also be giving a sanding demonstration using the disk sander and the vertical sander.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on projects.
Pd. 2,3 Plastics Technology: Students will continue to work on the desk organizer project.
Thursday 11/3
Pd. 1,4,7 Basic Wood: Students will be sanding using the disc sander and the vertical sander.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on projects
Pd. 2,3 Plastics Technology: Students will be finishing the desk organizer today. If there is enough time left in the class period we will be starting the next project which will be the acrylic mug.
Friday 11/4
Pd. 1,4,7 Basic Wood: I will give a demonstration on cutting the center brace for the bench the students will be using the power cut off saw. Students will be given a study sheet for the power cut off saw and then the following day will be given a quiz on the piece of equipment. They must pass the test before they may use it.
Pd. 5 Advanced Cabinetmaking: Students will continue t6o work on projects. I will be helping students with all processes as the work on projects.
Pd. 2,3 Plastics Technology: If demonstration was not given on Thursday on making the acrylic mug this will be done today. This demonstration will be done in two parts. The first part will be sanding the ends of the acrylic tube. We will then choose the color for the bottom. I will then demon straight how students will cut the bottom out and glue it to one end of the tube.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Assessments; Will be done by Question and Answers and Quiz.
Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (10/31/2011 to 11/4/2011)
Monday 10/31 *Due to repairs on a pipe in the wood shop we will be out of the shop on Monday or Tuesday. We will be over in the Power Tech room or the Health Room*
Pd. 1,4,7 Basic Wood: I will be giving a demonstration on Laying out of the angles to be cut on the bench ends. They will also be tracing the radius on the bottom edge of pieces. I will then give a demonstration on using the Band saw to cut the project pieces out. We will be using three different Band Saws. Students may choose which one they are more comfortable using.
Pd. 5 Advanced Cabinetmaking: I will give a demonstration using the Power Miter Saw to the advanced class and the test will be given the following Day.
Pd. 2,3 Plastics Technology: Students will continue with the desk organizer project. They will be gluing together. After 24 hours they will be sanding using three different grits of sand paper.
Tuesday 11/1
Pd. 1,4,7 Basic Wood: Students will continue to cut project pieces out.
Pd. 5 Advanced Cabinetmaking: Test will be given on the power miter saw. Students will continue to work on individual projects. As students get to different processes with project part construction I will be give group demonstrations’.
Pd. 2,3 Plastics Technology: I will give a demonstration on buffing the project. There is a specific order to follow in buffing this project.
WENDNESDAY 11/2
Pd. 1,4,7 Basic Wood: Students will continue to cut project pieces out. I will also be giving a sanding demonstration using the disk sander and the vertical sander.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on projects.
Pd. 2,3 Plastics Technology: Students will continue to work on the desk organizer project.
Thursday 11/3
Pd. 1,4,7 Basic Wood: Students will be sanding using the disc sander and the vertical sander.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on projects
Pd. 2,3 Plastics Technology: Students will be finishing the desk organizer today. If there is enough time left in the class period we will be starting the next project which will be the acrylic mug.
Friday 11/4
Pd. 1,4,7 Basic Wood: I will give a demonstration on cutting the center brace for the bench the students will be using the power cut off saw. Students will be given a study sheet for the power cut off saw and then the following day will be given a quiz on the piece of equipment. They must pass the test before they may use it.
Pd. 5 Advanced Cabinetmaking: Students will continue t6o work on projects. I will be helping students with all processes as the work on projects.
Pd. 2,3 Plastics Technology: If demonstration was not given on Thursday on making the acrylic mug this will be done today. This demonstration will be done in two parts. The first part will be sanding the ends of the acrylic tube. We will then choose the color for the bottom. I will then demon straight how students will cut the bottom out and glue it to one end of the tube.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Assessments; Will be done by Question and Answers and Quiz.
Monday, October 17, 2011
LESSON PLAN
Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (10/17/2011 to 10/21/2011)
Monday 10/17
Pd. 1,4,7 Basic Wood: Students will be working on working on the Router project with the Plunge Router. They will be doing their name or a sports team only.
Pd. 5 Advanced Cabinetmaking: Students are in the process of planning lumber down and getting wood ready to glue together. Students will continue with gluing
Pd. 2,3 Plastics Technology: We will be cutting the plug for the end. I will be giving a demonstration on drilling the small holes in the end for salt and pepper to come out.
Tuesday 10/18
Pd. 1,4,7 Basic Wood: Students will continue with Plunge Router project and sanding . They will also router all the edges on the router table. I will also be giving a demonstration on staining and explaining the differences between Paint and Stain. The differences between some stains.
Pd. 5 Advanced Cabinetmaking: Students will continue to plane and cut lumber down for projects. I will give a review demonstration cutting a project piece down to the exact size and making sure that it is perfectly square.
Pd. 2,3 Plastics Technology: Students will continue to drill small holes we will finish cutting the plugs for the large hole.
WENDNESDAY 10/19
Pd. 1,4,7 Basic Wood: Some students will be finishing up on the plunge router. Other students will be starting to stain. They will be staining both router projects.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on projects. I will be around to each student to inspect their progress and to make sure they are not making any major mistakes.
Pd. 2,3 Plastics Technology: Students will be finishing up any buffing and polishing and I will be grading their projects. Students will bring them up one by one so we can talk about the problems thy may have had doing this project.
Thursday 10/20
Pd. 1,4,7 Basic Wood: Students will continue with staining. This will take two days to finish.
Pd. 5 Advanced Cabinetmaking: Students will continue to cut projects to finish sizes. I will give a demonstration on sanding. We will talk about going through a progression of steps to achieve the best quality finish.
Pd. 2,3 Plastics Technology: I will be finishing grading first. I will then start a demonstration on making a desk organizer out of acrylic. We will be gluing pieces together using the squeeze bottles. This demonstration will take most of the period.
Friday 10/21
Pd. 1,4,7 Basic Wood: Students will finish staining. Students who were done staining before today will be painting the inside of the letters if they choose.
Pd. 5 Advanced Cabinetmaking: I will be giving a demonstration of different types of joints that are used in cabinet construction I will start out with the Dado Joints. I will be showing how they are cut using the table saw.
Pd. 2,3 Plastics Technology: Students will be working on the desk organizer project this will take approximately there days till all students are done.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Assessments; Will be done by Question and Answers and Quiz.
Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (10/17/2011 to 10/21/2011)
Monday 10/17
Pd. 1,4,7 Basic Wood: Students will be working on working on the Router project with the Plunge Router. They will be doing their name or a sports team only.
Pd. 5 Advanced Cabinetmaking: Students are in the process of planning lumber down and getting wood ready to glue together. Students will continue with gluing
Pd. 2,3 Plastics Technology: We will be cutting the plug for the end. I will be giving a demonstration on drilling the small holes in the end for salt and pepper to come out.
Tuesday 10/18
Pd. 1,4,7 Basic Wood: Students will continue with Plunge Router project and sanding . They will also router all the edges on the router table. I will also be giving a demonstration on staining and explaining the differences between Paint and Stain. The differences between some stains.
Pd. 5 Advanced Cabinetmaking: Students will continue to plane and cut lumber down for projects. I will give a review demonstration cutting a project piece down to the exact size and making sure that it is perfectly square.
Pd. 2,3 Plastics Technology: Students will continue to drill small holes we will finish cutting the plugs for the large hole.
WENDNESDAY 10/19
Pd. 1,4,7 Basic Wood: Some students will be finishing up on the plunge router. Other students will be starting to stain. They will be staining both router projects.
Pd. 5 Advanced Cabinetmaking: Students will continue to work on projects. I will be around to each student to inspect their progress and to make sure they are not making any major mistakes.
Pd. 2,3 Plastics Technology: Students will be finishing up any buffing and polishing and I will be grading their projects. Students will bring them up one by one so we can talk about the problems thy may have had doing this project.
Thursday 10/20
Pd. 1,4,7 Basic Wood: Students will continue with staining. This will take two days to finish.
Pd. 5 Advanced Cabinetmaking: Students will continue to cut projects to finish sizes. I will give a demonstration on sanding. We will talk about going through a progression of steps to achieve the best quality finish.
Pd. 2,3 Plastics Technology: I will be finishing grading first. I will then start a demonstration on making a desk organizer out of acrylic. We will be gluing pieces together using the squeeze bottles. This demonstration will take most of the period.
Friday 10/21
Pd. 1,4,7 Basic Wood: Students will finish staining. Students who were done staining before today will be painting the inside of the letters if they choose.
Pd. 5 Advanced Cabinetmaking: I will be giving a demonstration of different types of joints that are used in cabinet construction I will start out with the Dado Joints. I will be showing how they are cut using the table saw.
Pd. 2,3 Plastics Technology: Students will be working on the desk organizer project this will take approximately there days till all students are done.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Assessments; Will be done by Question and Answers and Quiz.
Monday, October 10, 2011
LESSON PLAN
Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (10/10/2011 to 10/14/2011)
Monday 10/10
Pd. 1,4,7 Basic Wood: Students will be finishing the Free Hand routering project. We will also be planeing lumber down For our next router project. This will take the whole period. We will be using Poplar.
Pd. 5 Advanced Cabinetmaking: Students are in the process of planning lumber down and getting wood ready to glue together. I will be giving a demonstration on gluing along edge grain. Students will learn proper procedures and what to look for when gluing.
Pd. 2,3 Plastics Technology: I will be giving a demonstration on drilling 11/16” hole in each of their blocks and then tapping it with the threading tool.
Tuesday 10/11
Pd. 1,4,7 Basic Wood: I will be giving a demonstration on the Plunge router and using the letter jig to create our next router project. This demo will take most of the period. I want the students to have a full understanding of how the plunge router will be used and how we will be using the letter jigs to create a perfect name plate.
Pd. 5 Advanced Cabinetmaking:
Pd. 2,3 Plastics Technology: Students will continue with drilling and tapping.
WENDNESDAY 10/12
Pd. 1,4,7 Basic Wood: We will be planning lumber down for the plunge router project. This will take the entire period.
Pd. 5 Advanced Cabinetmaking: Students will continue to plane lumber down and glue stock together.
Pd. 2,3 Plastics Technology: Students will continue drilling and tapping. I will be making the threaded plugs for the blocks.
Thursday 10/13
Pd. 1,4,7 Basic Wood: Students will be starting the plunge router project. This project will take approximately three days due to the amount of students in the classes. Students can also use the free hand router if they choose to do extra.
Pd. 5 Advanced Cabinetmaking: Students will continue with projects. Some students will be cutting out parts for projects at this point.
Pd. 2,3 Plastics Technology: Students will continue drilling and tapping. Some will be finishing up by giving their projects a final polish on the wheel.
Friday 10/14 I will not be in school students will have work to do.
Pd. 1,4,7 Basic Wood:
Pd. 5 Advanced Cabinetmaking:
Pd. 2,3 Plastics Technology:
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Assessments; Will be done by Question and Answers and Quiz.
Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (10/10/2011 to 10/14/2011)
Monday 10/10
Pd. 1,4,7 Basic Wood: Students will be finishing the Free Hand routering project. We will also be planeing lumber down For our next router project. This will take the whole period. We will be using Poplar.
Pd. 5 Advanced Cabinetmaking: Students are in the process of planning lumber down and getting wood ready to glue together. I will be giving a demonstration on gluing along edge grain. Students will learn proper procedures and what to look for when gluing.
Pd. 2,3 Plastics Technology: I will be giving a demonstration on drilling 11/16” hole in each of their blocks and then tapping it with the threading tool.
Tuesday 10/11
Pd. 1,4,7 Basic Wood: I will be giving a demonstration on the Plunge router and using the letter jig to create our next router project. This demo will take most of the period. I want the students to have a full understanding of how the plunge router will be used and how we will be using the letter jigs to create a perfect name plate.
Pd. 5 Advanced Cabinetmaking:
Pd. 2,3 Plastics Technology: Students will continue with drilling and tapping.
WENDNESDAY 10/12
Pd. 1,4,7 Basic Wood: We will be planning lumber down for the plunge router project. This will take the entire period.
Pd. 5 Advanced Cabinetmaking: Students will continue to plane lumber down and glue stock together.
Pd. 2,3 Plastics Technology: Students will continue drilling and tapping. I will be making the threaded plugs for the blocks.
Thursday 10/13
Pd. 1,4,7 Basic Wood: Students will be starting the plunge router project. This project will take approximately three days due to the amount of students in the classes. Students can also use the free hand router if they choose to do extra.
Pd. 5 Advanced Cabinetmaking: Students will continue with projects. Some students will be cutting out parts for projects at this point.
Pd. 2,3 Plastics Technology: Students will continue drilling and tapping. Some will be finishing up by giving their projects a final polish on the wheel.
Friday 10/14 I will not be in school students will have work to do.
Pd. 1,4,7 Basic Wood:
Pd. 5 Advanced Cabinetmaking:
Pd. 2,3 Plastics Technology:
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Assessments; Will be done by Question and Answers and Quiz.
Tuesday, October 4, 2011
LESSON PLAN
Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (10/3/2011 to 10/7/2011)
Monday 10/3
Pd. 1,4,7 Basic Wood: We will be starting are first project together. We will be planeing Poplar boards down to ¾”. We will do this together so all students have an opportunity to perform the steps need to run the planer safely under my close super vision. My objective for students is to fully understand how to safely use this machine.
Pd. 5 Advanced Cabinetmaking: Students will be working on finding project plans and having them approved by me. I will be helping students locate project plans on the computer and printing them out.
Pd. 2,3 Plastics Technology: We will be working on cutting the 2” X 4” block apart into two 1 ¾” X 1 ¾” blocks. We will be using the table saw to perform this process. This will take proximity two class periods to cut all of them to size.
Tuesday 10/4
Pd. 1,4,7 Basic Wood: I will be giving a demonstration on using the two different types of router we have in the shop. This will be and in-depth demonstration and will take the entire period. We will use the fixed router and the Plunge router. Students will need to decide what they will be putting on the two boards they will be doing. They may choose from their names or a sports team.
Pd. 5 Advanced Cabinetmaking: I will be lecturing on how to figure out how much would will be used to make their projects and also how much it will cost.
Pd. 2,3 Plastics Technology: We will continue with cutting the blocks to size. I will also give students a demonstration on sanding the blocks on the 12” disc sander. I will give demonstration on sanding using the hand sanders with 100 grit paper.
WENDNESDAY 10/5
Pd. 1,4,7 Basic Wood: Students will first be doing the free hand project. This will take approximately two days to finish the free hand project. I will be supervising each student that is routering at the time.
Pd. 5 Advanced Cabinetmaking: Students will be working on deciding what kind of wood they will be using and figuring out the amount of wood and the cost of the wood before they start to work.
Pd. 2,3 Plastics Technology: Students will continue with Sanding of blocks. They will go through a four step processes of using four different grits.
Thursday 10/6
Pd. 1,4,7 Basic Wood: Students will continue to work on the free hand routering project. Will give a demonstration on sanding the project during the first part of class.
Pd. 5 Advanced Cabinetmaking: Students will be picking out the wood for their projects and will start to plane lumber down.
Pd. 2,3 Plastics Technology: Students will continue to sand blocks down using the sanding steps described in the demonstration
Friday 10/7
Pd. 1,4,7 Basic
Wood: Students will continue with the present work.
Pd. 5 Advanced Cabinetmaking: Students will continue with the present work.
Pd. 2,3 Plastics Technology: Students will continue with the present work.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Assessments; Will be done by Question and Answers and Quiz.
Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (10/3/2011 to 10/7/2011)
Monday 10/3
Pd. 1,4,7 Basic Wood: We will be starting are first project together. We will be planeing Poplar boards down to ¾”. We will do this together so all students have an opportunity to perform the steps need to run the planer safely under my close super vision. My objective for students is to fully understand how to safely use this machine.
Pd. 5 Advanced Cabinetmaking: Students will be working on finding project plans and having them approved by me. I will be helping students locate project plans on the computer and printing them out.
Pd. 2,3 Plastics Technology: We will be working on cutting the 2” X 4” block apart into two 1 ¾” X 1 ¾” blocks. We will be using the table saw to perform this process. This will take proximity two class periods to cut all of them to size.
Tuesday 10/4
Pd. 1,4,7 Basic Wood: I will be giving a demonstration on using the two different types of router we have in the shop. This will be and in-depth demonstration and will take the entire period. We will use the fixed router and the Plunge router. Students will need to decide what they will be putting on the two boards they will be doing. They may choose from their names or a sports team.
Pd. 5 Advanced Cabinetmaking: I will be lecturing on how to figure out how much would will be used to make their projects and also how much it will cost.
Pd. 2,3 Plastics Technology: We will continue with cutting the blocks to size. I will also give students a demonstration on sanding the blocks on the 12” disc sander. I will give demonstration on sanding using the hand sanders with 100 grit paper.
WENDNESDAY 10/5
Pd. 1,4,7 Basic Wood: Students will first be doing the free hand project. This will take approximately two days to finish the free hand project. I will be supervising each student that is routering at the time.
Pd. 5 Advanced Cabinetmaking: Students will be working on deciding what kind of wood they will be using and figuring out the amount of wood and the cost of the wood before they start to work.
Pd. 2,3 Plastics Technology: Students will continue with Sanding of blocks. They will go through a four step processes of using four different grits.
Thursday 10/6
Pd. 1,4,7 Basic Wood: Students will continue to work on the free hand routering project. Will give a demonstration on sanding the project during the first part of class.
Pd. 5 Advanced Cabinetmaking: Students will be picking out the wood for their projects and will start to plane lumber down.
Pd. 2,3 Plastics Technology: Students will continue to sand blocks down using the sanding steps described in the demonstration
Friday 10/7
Pd. 1,4,7 Basic
Wood: Students will continue with the present work.
Pd. 5 Advanced Cabinetmaking: Students will continue with the present work.
Pd. 2,3 Plastics Technology: Students will continue with the present work.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Assessments; Will be done by Question and Answers and Quiz.
Thursday, September 29, 2011
LESSON PLAN
Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (9/26/2011 to 9/30/2011)
Monday 9/26
Pd. 1,4,7 Basic Wood: In today’s class we will be going over the Drill press. I will give the students an in-depth presentation of this machine and all the safety instructions needed to safely operate this machine. My objective for students is to fully understand how to safely use this machine.
Pd. 5 Advanced Cabinetmaking: In today’s class we will be going over the Drill press. I will give the students an in-depth presentation of this machine and all the safety instructions needed to safely operate this machine. My objective for students is to fully understand how to safely use this machine.
Pd. 2,3 Plastics Technology: In plastics I will be giving a demonstration on gluing Acrylic together and pressing under high pressure. This will be for our Salt and Pepper Shaker project. Students will be using two colors of Acrylic. They will all receive 10 pieces of each color 2” X 4”, and a press box.
Tuesday 9/27 ( I will be out of school on this Day)
Pd. 1,4,7 Basic Wood: Students will be taking the test on the Band Saw and the Drill press. Students who are done early will have study time.
Pd. 5 Advanced Cabinetmaking: Students will be taking the test on the Band Saw and the Drill press. Students who are done early will have study time.
Pd. 2,3 Plastics Technology: Have students read Chapter 20 page 208 in the Industrial arts Plastics book and have students do the 13 questions at the end of the chapter on page 227
WENDNESDAY 9/28
Pd. 1,4,7 Basic Wood: I will be giving a demonstration on the Disc and belt sander and the Vertical Oscillating Sander. They must have a full understanding of these machines. Any students who need to make up any test will do so provide enough time is left in the class period.
Pd. 5 Advanced Cabinetmaking: I will be giving a demonstration on the Disc and belt sander and the Vertical Oscillating Sander. They must have a full understanding of these machines. Any students who need to make up any test will do so provide enough time is left in the class period.
Pd. 2,3 Plastics Technology: Students will peel all the protective paper from all Acrylic piece and start to stack the in the press box and apply glue between each piece of Acrylic and then we will place them in the Vice to apply pressure.
Thursday 9/29
Pd. 1,4,7 Basic Wood: I will be showing a safety video on the use of the Power miter saw from You Tube. I will be giving a full in-depth demonstration of the Power miter saw. This will take the entire length of the class.
Pd. 5 Advanced Cabinetmaking: I will be showing a safety video on the use of the Power miter saw from You Tube. I will be giving a full in-depth demonstration of the Power miter saw. This will take the entire length of the class.
Pd. 2,3 Plastics Technology: We will continue with the process for any students that did not get to the pressing process on Wednesday Other students will remove the acyclic cube from the press box.
Friday 9/30
Pd. 1,4,7 Basic Wood:
Pd. 5 Advanced Cabinetmaking:
Pd. 2,3 Plastics Technology: We will continue with the press and removal of cubes from the press box. I will be giving a demonstration on the the first step of cutting the cube to the exact size.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Assessments; Will be done by Question and Answers and Quiz.
Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (9/26/2011 to 9/30/2011)
Monday 9/26
Pd. 1,4,7 Basic Wood: In today’s class we will be going over the Drill press. I will give the students an in-depth presentation of this machine and all the safety instructions needed to safely operate this machine. My objective for students is to fully understand how to safely use this machine.
Pd. 5 Advanced Cabinetmaking: In today’s class we will be going over the Drill press. I will give the students an in-depth presentation of this machine and all the safety instructions needed to safely operate this machine. My objective for students is to fully understand how to safely use this machine.
Pd. 2,3 Plastics Technology: In plastics I will be giving a demonstration on gluing Acrylic together and pressing under high pressure. This will be for our Salt and Pepper Shaker project. Students will be using two colors of Acrylic. They will all receive 10 pieces of each color 2” X 4”, and a press box.
Tuesday 9/27 ( I will be out of school on this Day)
Pd. 1,4,7 Basic Wood: Students will be taking the test on the Band Saw and the Drill press. Students who are done early will have study time.
Pd. 5 Advanced Cabinetmaking: Students will be taking the test on the Band Saw and the Drill press. Students who are done early will have study time.
Pd. 2,3 Plastics Technology: Have students read Chapter 20 page 208 in the Industrial arts Plastics book and have students do the 13 questions at the end of the chapter on page 227
WENDNESDAY 9/28
Pd. 1,4,7 Basic Wood: I will be giving a demonstration on the Disc and belt sander and the Vertical Oscillating Sander. They must have a full understanding of these machines. Any students who need to make up any test will do so provide enough time is left in the class period.
Pd. 5 Advanced Cabinetmaking: I will be giving a demonstration on the Disc and belt sander and the Vertical Oscillating Sander. They must have a full understanding of these machines. Any students who need to make up any test will do so provide enough time is left in the class period.
Pd. 2,3 Plastics Technology: Students will peel all the protective paper from all Acrylic piece and start to stack the in the press box and apply glue between each piece of Acrylic and then we will place them in the Vice to apply pressure.
Thursday 9/29
Pd. 1,4,7 Basic Wood: I will be showing a safety video on the use of the Power miter saw from You Tube. I will be giving a full in-depth demonstration of the Power miter saw. This will take the entire length of the class.
Pd. 5 Advanced Cabinetmaking: I will be showing a safety video on the use of the Power miter saw from You Tube. I will be giving a full in-depth demonstration of the Power miter saw. This will take the entire length of the class.
Pd. 2,3 Plastics Technology: We will continue with the process for any students that did not get to the pressing process on Wednesday Other students will remove the acyclic cube from the press box.
Friday 9/30
Pd. 1,4,7 Basic Wood:
Pd. 5 Advanced Cabinetmaking:
Pd. 2,3 Plastics Technology: We will continue with the press and removal of cubes from the press box. I will be giving a demonstration on the the first step of cutting the cube to the exact size.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Assessments; Will be done by Question and Answers and Quiz.
Wednesday, September 21, 2011
LESSON PLAN
Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (9/19/2011 to 9/23/2011)
Monday 9/19
Pd. 1,4,7 Basic Wood: Students will be given a demonstration on the safe and proper use of the Planer. We will talk about all safety procedures that must be followed in order for the students to safely use the Planner. They will learn all parts and there specific purpose. This will take the entire period.
Pd. 5 Advanced Cabinetmaking: Students will be given a demonstration on the safe and proper use of the Planer. We will talk about all safety procedures that must be followed in order for the students to safely use the Planner. They will learn all parts and there specific purpose. This will take the entire period.
Pd. 2,3 Plastics Technology: We will be talking about heat forming Acrylic. I will be giving a demonstration on using the strip heater we will be making a self standing 4” X 6” clear acrylic picture frame. We will be using 1/16” sheeting. Each student will make one 4” X 6” frame.
Tuesday 9/20
Pd. 1,4,7 Basic Wood: Students will be given a demonstration on the safe and proper use of the Jointer. We will talk about all safety procedures that must be followed in order for the students to safely use the Jointer. They will learn all parts and there specific purpose. This will take the entire period.
Pd. 5 Advanced Cabinetmaking: Students will be given a demonstration on the safe and proper use of the Jointer. We will talk about all safety procedures that must be followed in order for the students to safely use the Jointer. They will learn all parts and there specific purpose. This will take the entire period.
Pd. 2,3 Plastics Technology: We will be returning to the Blow molding machine To make a 10” Serving tray. Due to a mold malfunction we had to go to the picture frame project but I was able to repair the mold.
WENDNESDAY 9/21
Pd. 1,4,7 Basic Wood: Students will be taking a Safety test on the Planer and the Jointer. The test will consist of True False questions and a parts identification section. They will be provided a Word back for each test. All students must pass these safety tests before they may use the equipment.
Pd. 5 Advanced Cabinetmaking: Students will be taking a Safety test on the Planer and the Jointer. The test will consist of True False questions and a parts identification section. They will be provided a Word back for each test. All students must pass these safety tests before they may use the equipment.
Pd. 2,3 Plastics Technology: Today I am going to be showing the class how large signs and many other products are made by industries today by using the Vacuum method. We will be use YOU TUBE for this.
Thursday 9/22
Pd. 1,4,7 Basic Wood: Students will be given a demonstration on the safe and proper use of the Table Saw. We will talk about all safety procedures that must be followed in order for the students to safely use the Jointer. They will learn all parts and there specific purpose. This will take the entire period.
Pd. 5 Advanced Cabinetmaking: Students will be given a demonstration on the safe and proper use of the Table Saw. We will talk about all safety procedures that must be followed in order for the students to safely use the Jointer. They will learn all parts and there specific purpose. This will take the entire period.
Pd. 2,3 Plastics Technology: Today I will be giving a demonstration on Vacuum Molding using the same machine that we used for our blow molding projects. This demonstration will take the entire period.
Friday 9/23
Pd. 1,4,7 Basic Wood: Students will be taking a Safety test on the Table Saw. The test will consist of True False questions and a parts identification section. They will be provided a Word back for each test. All students must pass these safety tests before they may use the equipment.
Pd. 5 Advanced Cabinetmaking: Students will be taking a Safety test on the Table Saw. The test will consist of True False questions and a parts identification section. They will be provided a Word back for each test. All students must pass these safety tests before they may use the equipment.
Pd. 2,3 Plastics Technology: We will be preparing are plastic the Vacuum molding project. And students will start with project. It will take two days for students to finish this project.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Assessments; Will be done by Question and Answers and Quiz.
Kevin Scheib (Wood Shop and Plastics Technology) weekly lesson plans (9/19/2011 to 9/23/2011)
Monday 9/19
Pd. 1,4,7 Basic Wood: Students will be given a demonstration on the safe and proper use of the Planer. We will talk about all safety procedures that must be followed in order for the students to safely use the Planner. They will learn all parts and there specific purpose. This will take the entire period.
Pd. 5 Advanced Cabinetmaking: Students will be given a demonstration on the safe and proper use of the Planer. We will talk about all safety procedures that must be followed in order for the students to safely use the Planner. They will learn all parts and there specific purpose. This will take the entire period.
Pd. 2,3 Plastics Technology: We will be talking about heat forming Acrylic. I will be giving a demonstration on using the strip heater we will be making a self standing 4” X 6” clear acrylic picture frame. We will be using 1/16” sheeting. Each student will make one 4” X 6” frame.
Tuesday 9/20
Pd. 1,4,7 Basic Wood: Students will be given a demonstration on the safe and proper use of the Jointer. We will talk about all safety procedures that must be followed in order for the students to safely use the Jointer. They will learn all parts and there specific purpose. This will take the entire period.
Pd. 5 Advanced Cabinetmaking: Students will be given a demonstration on the safe and proper use of the Jointer. We will talk about all safety procedures that must be followed in order for the students to safely use the Jointer. They will learn all parts and there specific purpose. This will take the entire period.
Pd. 2,3 Plastics Technology: We will be returning to the Blow molding machine To make a 10” Serving tray. Due to a mold malfunction we had to go to the picture frame project but I was able to repair the mold.
WENDNESDAY 9/21
Pd. 1,4,7 Basic Wood: Students will be taking a Safety test on the Planer and the Jointer. The test will consist of True False questions and a parts identification section. They will be provided a Word back for each test. All students must pass these safety tests before they may use the equipment.
Pd. 5 Advanced Cabinetmaking: Students will be taking a Safety test on the Planer and the Jointer. The test will consist of True False questions and a parts identification section. They will be provided a Word back for each test. All students must pass these safety tests before they may use the equipment.
Pd. 2,3 Plastics Technology: Today I am going to be showing the class how large signs and many other products are made by industries today by using the Vacuum method. We will be use YOU TUBE for this.
Thursday 9/22
Pd. 1,4,7 Basic Wood: Students will be given a demonstration on the safe and proper use of the Table Saw. We will talk about all safety procedures that must be followed in order for the students to safely use the Jointer. They will learn all parts and there specific purpose. This will take the entire period.
Pd. 5 Advanced Cabinetmaking: Students will be given a demonstration on the safe and proper use of the Table Saw. We will talk about all safety procedures that must be followed in order for the students to safely use the Jointer. They will learn all parts and there specific purpose. This will take the entire period.
Pd. 2,3 Plastics Technology: Today I will be giving a demonstration on Vacuum Molding using the same machine that we used for our blow molding projects. This demonstration will take the entire period.
Friday 9/23
Pd. 1,4,7 Basic Wood: Students will be taking a Safety test on the Table Saw. The test will consist of True False questions and a parts identification section. They will be provided a Word back for each test. All students must pass these safety tests before they may use the equipment.
Pd. 5 Advanced Cabinetmaking: Students will be taking a Safety test on the Table Saw. The test will consist of True False questions and a parts identification section. They will be provided a Word back for each test. All students must pass these safety tests before they may use the equipment.
Pd. 2,3 Plastics Technology: We will be preparing are plastic the Vacuum molding project. And students will start with project. It will take two days for students to finish this project.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Plastics- To have students fully understand process of how to use different types of measuring devices and how to measure accurately. Students will also learn safe and acceptable procedure for the shop.
Assessments; Will be done by Question and Answers and Quiz.
Monday, May 23, 2011
LESSON PLAN
Kevin Scheib (Wood Shop) weekly lesson plans (5/23/11/2011-5/26/2011)
Monday 5/23/11 We will be following the testing schedule and the two hour schedule.
Pd. 4,5 Plastics: 5th pd seniors will be taking finals. Others students will be studying for finals.
Pd. 2,3,6 Basic Wood Working : 3rd pd. seniors Will be taking finals. Others students will be studying for finals.
Pd. 7 Advanced Cabinet Making: Students will be studying for finals.
TUESDAY 5/24/11
Pd. 4,5 Plastics: Students will be studying for finals.
Pd. 2,3,6 Basic Wood Working: 2nd pd seniors students will be taking finals
Pd. 7 Advanced Cabinet Making: Students will be studying for finals.
WENDNESDAY 5/24/11
Pd. 4,5 Plastics: Students will be studying in finals.
Pd. 2,3,6 BASIC WOOD WORKING: 6th pd. seniors will be taking finals. Others students will be studying for finals.
Pd. 7 Advanced Cabinet Making: 7th pd. seniors will be taking finals. Others students will be studying for finals.
THURSDAY 5/26/11
Pd. 4,5 Plastics: 4th pd. seniors will be taking finals. Others students will be studying for finals.
Pd. 2,3,6 Basic Wood Working: Students will be studying for finals.
Pd.7 Advanced Cabinet Making: Students will be studying for finals.
FRIDAY 5/27/11
Pd. 4,5 Plastics: Students will be studying for finals.
Pd. 2,3,6 Basic Wood Work: 6th pd students will be taking finals.
Pd. 7 Advanced Cabinet Making: 7th pd. students will be taking finals.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz and Project review and student performance.
Kevin Scheib (Wood Shop) weekly lesson plans (5/23/11/2011-5/26/2011)
Monday 5/23/11 We will be following the testing schedule and the two hour schedule.
Pd. 4,5 Plastics: 5th pd seniors will be taking finals. Others students will be studying for finals.
Pd. 2,3,6 Basic Wood Working : 3rd pd. seniors Will be taking finals. Others students will be studying for finals.
Pd. 7 Advanced Cabinet Making: Students will be studying for finals.
TUESDAY 5/24/11
Pd. 4,5 Plastics: Students will be studying for finals.
Pd. 2,3,6 Basic Wood Working: 2nd pd seniors students will be taking finals
Pd. 7 Advanced Cabinet Making: Students will be studying for finals.
WENDNESDAY 5/24/11
Pd. 4,5 Plastics: Students will be studying in finals.
Pd. 2,3,6 BASIC WOOD WORKING: 6th pd. seniors will be taking finals. Others students will be studying for finals.
Pd. 7 Advanced Cabinet Making: 7th pd. seniors will be taking finals. Others students will be studying for finals.
THURSDAY 5/26/11
Pd. 4,5 Plastics: 4th pd. seniors will be taking finals. Others students will be studying for finals.
Pd. 2,3,6 Basic Wood Working: Students will be studying for finals.
Pd.7 Advanced Cabinet Making: Students will be studying for finals.
FRIDAY 5/27/11
Pd. 4,5 Plastics: Students will be studying for finals.
Pd. 2,3,6 Basic Wood Work: 6th pd students will be taking finals.
Pd. 7 Advanced Cabinet Making: 7th pd. students will be taking finals.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz and Project review and student performance.
Monday, March 28, 2011
LESSON PLAN
Kevin Scheib (Wood Shop) weekly lesson plans (3/28/11/2011-4/1/2011) Will be fallowing the Test Schedule
Monday 3/28/11
Pd. 4,5 Plastics: Some students will continue to work on the clip board project. We will be putting the clips on using 3/32” pop rivets. Students who are finished will continue to assemble parts for the Kayak.
Pd. 2,3,6 Basic Wood Working : Students will continue to work on projects. Many students are starting to assemble and stain projects. At this point in project production grate amount of individual one on one instruction.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects. Many students are starting to assemble and stain projects. At this point in project production grate amount of individual one on one instruction.
TUESDAY 3/29/11
Pd. 4,5 Plastics: Same processes will take place in this class as Monday.
Pd. 2,3,6 Basic Wood Working: Students are continuing with project work. Students are making grate head way. Will give a demonstration on pattern making using the arms for the rocking chair.
Pd. 7 Advanced Cabinet Making: : Students are continuing with project work. Students are making grate head way. Will give a demonstration on pattern making using the arms for the rocking chair.
WENDNESDAY3/30/11
Pd. 4,5 Plastics: We will start to assemble the bottom half of the kayak this will take some time to position all parts properly. We will be using screws to fasten all parts to the inner frame parts.
Pd. 2,3,6 BASIC WOOD WORKING: Students will continue to work on projects. Students who have stain projects will be clear coating projects. If it is a indoor project they will be using a water soluble clear coat. They will apply three coats.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects. Students who have stain projects will be clear coating projects. If it is a indoor project they will be using a water soluble clear coat. They will apply three coats.
THURSDAY3/31/11
Pd. 4,5 Plastics: We will make sure everything is in proper position and we will start to fiberglass all joints on the inside of the bottom parts. We will do this in front of the outside door so we can vent the air to the outside. We will put a insert in the door way so just the fan will fit in the hole.
Pd. 2,3,6 Basic Wood Working: Students will continue with projects. Students who are finished with projects will take all measurements and figure out the board footage and cost and turn it in to me.
Pd.7 Advanced Cabinet Making: Students will continue with projects. Students who are finished with projects will take all measurements and figure out the board footage and cost and turn it in to me.
FRIDAY 4/1/11
Pd. 4,5 Plastics: We will continue our work from Thursday of assembling the bottom half first.
Pd. 2,3,6 Basic Wood Work: Students will continue to work on projects.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz.
Kevin Scheib (Wood Shop) weekly lesson plans (3/28/11/2011-4/1/2011) Will be fallowing the Test Schedule
Monday 3/28/11
Pd. 4,5 Plastics: Some students will continue to work on the clip board project. We will be putting the clips on using 3/32” pop rivets. Students who are finished will continue to assemble parts for the Kayak.
Pd. 2,3,6 Basic Wood Working : Students will continue to work on projects. Many students are starting to assemble and stain projects. At this point in project production grate amount of individual one on one instruction.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects. Many students are starting to assemble and stain projects. At this point in project production grate amount of individual one on one instruction.
TUESDAY 3/29/11
Pd. 4,5 Plastics: Same processes will take place in this class as Monday.
Pd. 2,3,6 Basic Wood Working: Students are continuing with project work. Students are making grate head way. Will give a demonstration on pattern making using the arms for the rocking chair.
Pd. 7 Advanced Cabinet Making: : Students are continuing with project work. Students are making grate head way. Will give a demonstration on pattern making using the arms for the rocking chair.
WENDNESDAY3/30/11
Pd. 4,5 Plastics: We will start to assemble the bottom half of the kayak this will take some time to position all parts properly. We will be using screws to fasten all parts to the inner frame parts.
Pd. 2,3,6 BASIC WOOD WORKING: Students will continue to work on projects. Students who have stain projects will be clear coating projects. If it is a indoor project they will be using a water soluble clear coat. They will apply three coats.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects. Students who have stain projects will be clear coating projects. If it is a indoor project they will be using a water soluble clear coat. They will apply three coats.
THURSDAY3/31/11
Pd. 4,5 Plastics: We will make sure everything is in proper position and we will start to fiberglass all joints on the inside of the bottom parts. We will do this in front of the outside door so we can vent the air to the outside. We will put a insert in the door way so just the fan will fit in the hole.
Pd. 2,3,6 Basic Wood Working: Students will continue with projects. Students who are finished with projects will take all measurements and figure out the board footage and cost and turn it in to me.
Pd.7 Advanced Cabinet Making: Students will continue with projects. Students who are finished with projects will take all measurements and figure out the board footage and cost and turn it in to me.
FRIDAY 4/1/11
Pd. 4,5 Plastics: We will continue our work from Thursday of assembling the bottom half first.
Pd. 2,3,6 Basic Wood Work: Students will continue to work on projects.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz.
Monday, March 21, 2011
LESSON PLAN
Kevin Scheib (Wood Shop) weekly lesson plans (3/21/11/2011-3/25/2011)
Monday 3/21/11 No School
Pd. 4,5 Plastics: We know have all the patterns cut out and will start to assemble pattern pieces together using ¼” plywood pieces and wood glue to splice the pieces together.
Pd. 2,3,6 Basic Wood Working : Students will continue to work on projects. Many students are assembling projects. Many students are in the assembly phase of project construction. I will have to spend more one on one time with students who are assembling.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects. Many students are assembling projects. Many students are assembling projects. Many students are in the assembly phase of project construction. I will have to spend more one on one time with students who are assembling.
TUESDAY 3/22/11
Pd. 4,5 Plastics: We will continue splicing the pieces together. We will also be adding pieces of pine to the support pieces. So the sides can be screwed to the supports.
Pd. 2,3,6 Basic Wood Working: Students will continue to work on projects. Will give a refresher on plug cutting and sanding so students have a full understanding of the process.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects. Will give a refresher on plug cutting and sanding so students have a full understanding of the process.
WENDNESDAY3/23/11
Pd. 4,5 Plastics: Some students will be working on the clip board project while we are working fitting Kayak pieces together.
Pd. 2,3,6 BASIC WOOD WORKING: Students will continue to work on projects. Will give a refresher on using stain and the proper methods of applying stain. Many students are starting to stain and many projects are getting done.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects. Will give a refresher on using stain and the proper methods of applying stain. Many students are starting to stain and many projects are getting done.
THURSDAY3/24/11
Pd. 4,5 Plastics: We will start to assemble the bottom half of the Kayak first. We will be building the bottom half first and fiber glassing that first. This process could take some days to complete.
Pd. 2,3,6 Basic Wood Working: Students will continue to work on projects.
Pd.7 Advanced Cabinet Making: Students will continue to work on projects.
FRIDAY 3/25/11
Pd. 4,5 Plastics: We will continue our work from Thursday of assembling the bottom half first.
Pd. 2,3,6 Basic Wood Work: Students will continue to work on projects.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz.
Kevin Scheib (Wood Shop) weekly lesson plans (3/21/11/2011-3/25/2011)
Monday 3/21/11 No School
Pd. 4,5 Plastics: We know have all the patterns cut out and will start to assemble pattern pieces together using ¼” plywood pieces and wood glue to splice the pieces together.
Pd. 2,3,6 Basic Wood Working : Students will continue to work on projects. Many students are assembling projects. Many students are in the assembly phase of project construction. I will have to spend more one on one time with students who are assembling.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects. Many students are assembling projects. Many students are assembling projects. Many students are in the assembly phase of project construction. I will have to spend more one on one time with students who are assembling.
TUESDAY 3/22/11
Pd. 4,5 Plastics: We will continue splicing the pieces together. We will also be adding pieces of pine to the support pieces. So the sides can be screwed to the supports.
Pd. 2,3,6 Basic Wood Working: Students will continue to work on projects. Will give a refresher on plug cutting and sanding so students have a full understanding of the process.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects. Will give a refresher on plug cutting and sanding so students have a full understanding of the process.
WENDNESDAY3/23/11
Pd. 4,5 Plastics: Some students will be working on the clip board project while we are working fitting Kayak pieces together.
Pd. 2,3,6 BASIC WOOD WORKING: Students will continue to work on projects. Will give a refresher on using stain and the proper methods of applying stain. Many students are starting to stain and many projects are getting done.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects. Will give a refresher on using stain and the proper methods of applying stain. Many students are starting to stain and many projects are getting done.
THURSDAY3/24/11
Pd. 4,5 Plastics: We will start to assemble the bottom half of the Kayak first. We will be building the bottom half first and fiber glassing that first. This process could take some days to complete.
Pd. 2,3,6 Basic Wood Working: Students will continue to work on projects.
Pd.7 Advanced Cabinet Making: Students will continue to work on projects.
FRIDAY 3/25/11
Pd. 4,5 Plastics: We will continue our work from Thursday of assembling the bottom half first.
Pd. 2,3,6 Basic Wood Work: Students will continue to work on projects.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz.
Monday, February 28, 2011
LESSON PLAN
Kevin Scheib (Wood Shop) weekly lesson plans (2/28/11/2011-3/4/2011)26th week
Monday 2/28/11 No School
Pd. 4,5 Plastics: We will take a break from the Kayak project and continue with the pen holder project. Students will be pouring resin over their objects.
Pd. 2,3,6 Basic Wood Working : Students will continue to work on projects.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects.
TUESDAY 3/1/11
Pd. 4,5 Plastics: Students will continue to work on Pen Holder project. They will be Sanding and buffing. This is a long process. I will demonstrate how to apply the pen base to the base.
Pd. 2,3,6 Basic Wood Working: Students will continue to work on projects.
.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects.
WENDNESDAY3/2/11
Pd. 4,5 Plastics: I will give demonstration on making the paper weight project. Students will be using some sort of solid object that is fairly thin. We will be pouring it with the crystal clear resin.
Pd. 2,3,6 BASIC WOOD WORKING: Students will continue to work on projects.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects.
THURSDAY3/3/11
Pd. 4,5 Plastics: Students will be putting pen holders together and starting the paper weight project.
Pd. 2,3,6 Basic Wood Working: Students will continue to work on projects.
Pd.7 Advanced Cabinet Making: Students will continue to work on projects.
FRIDAY 3/4/11
Pd. 4,5 Plastics: Students who poured Thursday will be sanding and buffing today and other students will be pouring the project today.
Pd. 2,3,6 Basic Wood Work: Students will continue to work on projects.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz.
Kevin Scheib (Wood Shop) weekly lesson plans (2/28/11/2011-3/4/2011)26th week
Monday 2/28/11 No School
Pd. 4,5 Plastics: We will take a break from the Kayak project and continue with the pen holder project. Students will be pouring resin over their objects.
Pd. 2,3,6 Basic Wood Working : Students will continue to work on projects.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects.
TUESDAY 3/1/11
Pd. 4,5 Plastics: Students will continue to work on Pen Holder project. They will be Sanding and buffing. This is a long process. I will demonstrate how to apply the pen base to the base.
Pd. 2,3,6 Basic Wood Working: Students will continue to work on projects.
.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects.
WENDNESDAY3/2/11
Pd. 4,5 Plastics: I will give demonstration on making the paper weight project. Students will be using some sort of solid object that is fairly thin. We will be pouring it with the crystal clear resin.
Pd. 2,3,6 BASIC WOOD WORKING: Students will continue to work on projects.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects.
THURSDAY3/3/11
Pd. 4,5 Plastics: Students will be putting pen holders together and starting the paper weight project.
Pd. 2,3,6 Basic Wood Working: Students will continue to work on projects.
Pd.7 Advanced Cabinet Making: Students will continue to work on projects.
FRIDAY 3/4/11
Pd. 4,5 Plastics: Students who poured Thursday will be sanding and buffing today and other students will be pouring the project today.
Pd. 2,3,6 Basic Wood Work: Students will continue to work on projects.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz.
Tuesday, February 22, 2011
LESSON PLAN
Kevin Scheib (Wood Shop) weekly lesson plans (2/21/11/2011-2/25/2011)24th week
Monday 2/21/11 No School
Pd. 4,5 Plastics:
Pd. 2,3,6 Basic Wood Working :
Pd. 7 Advanced Cabinet Making:
TUESDAY 2/15/11
Pd. 4,5 Plastics: We will start to lay out patterns for the group project which will be the Kayak. This will be a combined project between both plastics classes. Students will also be working on the pen holder project at the same time.
Pd. 2,3,6 Basic Wood Working: Students will continue to work on projects.
.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects.
WENDNESDAY 2/16/11
Pd. 4,5 Plastics: We will continue to layout pattern pieces on the ¼” plywood
Pd. 2,3,6 BASIC WOOD WORKING: Students will continue to work on projects.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects.
THURSDAY 2/17/11
Pd. 4,5 Plastics: We will continue to layout pattern pieces on the ¼” plywood
Pd. 2,3,6 Basic Wood Working: Students will continue to work on projects.
Pd.7 Advanced Cabinet Making: Students will continue to work on projects.
FRIDAY 2/18/11
Pd. 4,5 Plastics: We will start to cut out the patterns using the hand held jig saw.
Pd. 2,3,6 Basic Wood Work: Students will continue to work on projects.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz.
Kevin Scheib (Wood Shop) weekly lesson plans (2/21/11/2011-2/25/2011)24th week
Monday 2/21/11 No School
Pd. 4,5 Plastics:
Pd. 2,3,6 Basic Wood Working :
Pd. 7 Advanced Cabinet Making:
TUESDAY 2/15/11
Pd. 4,5 Plastics: We will start to lay out patterns for the group project which will be the Kayak. This will be a combined project between both plastics classes. Students will also be working on the pen holder project at the same time.
Pd. 2,3,6 Basic Wood Working: Students will continue to work on projects.
.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects.
WENDNESDAY 2/16/11
Pd. 4,5 Plastics: We will continue to layout pattern pieces on the ¼” plywood
Pd. 2,3,6 BASIC WOOD WORKING: Students will continue to work on projects.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects.
THURSDAY 2/17/11
Pd. 4,5 Plastics: We will continue to layout pattern pieces on the ¼” plywood
Pd. 2,3,6 Basic Wood Working: Students will continue to work on projects.
Pd.7 Advanced Cabinet Making: Students will continue to work on projects.
FRIDAY 2/18/11
Pd. 4,5 Plastics: We will start to cut out the patterns using the hand held jig saw.
Pd. 2,3,6 Basic Wood Work: Students will continue to work on projects.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz.
Monday, February 14, 2011
LESSON PLAN
Kevin Scheib (Wood Shop) weekly lesson plans (2/14/2011-2/18/2011)24th week
Monday 2/14/11
Pd. 4,5 Plastics: Will give demonstration on pouring the pen holder project using a dollar bill.
Pd. 2,3,6 Basic Wood Working :
Pd. 7 Advanced Cabinet Making: Students will continue with layout and cutting of parts. Great strides are being made towards completion of projects.
TUESDAY 2/15/11
Pd. 4,5 Plastics: Will demonstrate sanding process of this project. We will go through three different levels of sanding. If time allows we will go to the buffing machine.
Pd. 2,3,6 Basic Wood Working: Students will continue to work on projects.
Pd. 7 Advanced Cabinet Making: Advanced students will continue to work on projects and basic wood work will continue cutting project parts.
WENDNESDAY 2/16/11
Pd. 4,5 Plastics: Will demonstrate buffing if we did not have enough time to move to next step on Tuesday.
Pd. 2,3,6 BASIC WOOD WORKING: Students will continue to work on Projects. I will set up the mortise machine and give demo on this machine again to refresh student’s memory.
Pd. 7 Advanced Cabinet Making: Students will continue to work on Projects. I will set up the mortise machine and give demo on this machine again to refresh students memory.
THURSDAY 2/17/11
Pd. 4,5 Plastics: Students will start pen holder project by preparing the mold and the object they intend on putting in the mold. Students will then pour first layer of resin in
Pd. 2,3,6 Basic Wood Working: Students will continue to with projects. I will continue to help students with any process that assistance is needed.
Pd.7 Advanced Cabinet Making: Students will continue to with projects. I will continue to help students with any process that assistance is needed.
FRIDAY 2/18/11
Pd. 4,5 Plastics: Students will continue with the pen holder project.
Pd. 2,3,6 Basic Wood Work: Students will continue with projects. Many students are starting to assemble projects.
Pd. 7 Advanced Cabinet Making: Students will continue with projects. Many students are starting to assemble projects.
Advanced students are making grate advances towards completion of projects,.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz.
Kevin Scheib (Wood Shop) weekly lesson plans (2/14/2011-2/18/2011)24th week
Monday 2/14/11
Pd. 4,5 Plastics: Will give demonstration on pouring the pen holder project using a dollar bill.
Pd. 2,3,6 Basic Wood Working :
Pd. 7 Advanced Cabinet Making: Students will continue with layout and cutting of parts. Great strides are being made towards completion of projects.
TUESDAY 2/15/11
Pd. 4,5 Plastics: Will demonstrate sanding process of this project. We will go through three different levels of sanding. If time allows we will go to the buffing machine.
Pd. 2,3,6 Basic Wood Working: Students will continue to work on projects.
Pd. 7 Advanced Cabinet Making: Advanced students will continue to work on projects and basic wood work will continue cutting project parts.
WENDNESDAY 2/16/11
Pd. 4,5 Plastics: Will demonstrate buffing if we did not have enough time to move to next step on Tuesday.
Pd. 2,3,6 BASIC WOOD WORKING: Students will continue to work on Projects. I will set up the mortise machine and give demo on this machine again to refresh student’s memory.
Pd. 7 Advanced Cabinet Making: Students will continue to work on Projects. I will set up the mortise machine and give demo on this machine again to refresh students memory.
THURSDAY 2/17/11
Pd. 4,5 Plastics: Students will start pen holder project by preparing the mold and the object they intend on putting in the mold. Students will then pour first layer of resin in
Pd. 2,3,6 Basic Wood Working: Students will continue to with projects. I will continue to help students with any process that assistance is needed.
Pd.7 Advanced Cabinet Making: Students will continue to with projects. I will continue to help students with any process that assistance is needed.
FRIDAY 2/18/11
Pd. 4,5 Plastics: Students will continue with the pen holder project.
Pd. 2,3,6 Basic Wood Work: Students will continue with projects. Many students are starting to assemble projects.
Pd. 7 Advanced Cabinet Making: Students will continue with projects. Many students are starting to assemble projects.
Advanced students are making grate advances towards completion of projects,.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz.
Monday, February 7, 2011
LESSON PLAN
Kevin Scheib (Wood Shop) weekly lesson plans (2/7/2011-2/11/2011)23rd week
Monday 2/7/11
Pd. 4,5 Plastics: Students will be drilling and tapping the threads into the bottom.
Pd. 2,3,6 Basic Wood Working : Students will continue with layout and cutting of parts.
Pd. 7 Advanced Cabinet Making: Students will continue with layout and cutting of parts.
TUESDAY 2/8/11
Pd. 4,5 Plastics: Students will be adding the threaded plug and drilling the small holes in the top.
Pd. 2,3,6 Basic Wood Working: Students will continue with work of cutting project parts.
Pd. 7 Advanced Cabinet Making: Advanced students will continue to work on projects and basic wood work will continue cutting project parts.
WENDNESDAY 2/9/11
Pd. 4,5 Plastics: Some Students will continue with buffing and drilling and taping.
Pd. 2,3,6 BASIC WOOD WORKING: I will give a glue up demonstration and students will continue to work on projects.
Pd. 7 Advanced Cabinet Making: I will give a glue up demonstration and students will continue to work on projects. Advanced students continue to work on projects.
THURSDAY 2/10/11
Pd. 4,5 Plastics: Students will be finishing the last steps today.
Pd. 2,3,6 Basic Wood Working: Students are working on their own. I will be assisting students with different processes as they arise. Will give a demonstration on planning lumber down after glued together.
Pd.7 Advanced Cabinet Making: Students are working on their own. I will be assisting students with different processes as they arise. Will give a demonstration on planning lumber down after glued together.
FRIDAY 2/11/11
Pd. 4,5 Plastics: Students will be designing there next project which will be the Clip board.
Pd. 2,3,6 Basic Wood Work: Students will continue to work on projects. When special operations are needed we will stop working and give a demonstration on that operation.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects. When special operations are needed we will stop working and give a demonstration on that operation.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz.
Kevin Scheib (Wood Shop) weekly lesson plans (2/7/2011-2/11/2011)23rd week
Monday 2/7/11
Pd. 4,5 Plastics: Students will be drilling and tapping the threads into the bottom.
Pd. 2,3,6 Basic Wood Working : Students will continue with layout and cutting of parts.
Pd. 7 Advanced Cabinet Making: Students will continue with layout and cutting of parts.
TUESDAY 2/8/11
Pd. 4,5 Plastics: Students will be adding the threaded plug and drilling the small holes in the top.
Pd. 2,3,6 Basic Wood Working: Students will continue with work of cutting project parts.
Pd. 7 Advanced Cabinet Making: Advanced students will continue to work on projects and basic wood work will continue cutting project parts.
WENDNESDAY 2/9/11
Pd. 4,5 Plastics: Some Students will continue with buffing and drilling and taping.
Pd. 2,3,6 BASIC WOOD WORKING: I will give a glue up demonstration and students will continue to work on projects.
Pd. 7 Advanced Cabinet Making: I will give a glue up demonstration and students will continue to work on projects. Advanced students continue to work on projects.
THURSDAY 2/10/11
Pd. 4,5 Plastics: Students will be finishing the last steps today.
Pd. 2,3,6 Basic Wood Working: Students are working on their own. I will be assisting students with different processes as they arise. Will give a demonstration on planning lumber down after glued together.
Pd.7 Advanced Cabinet Making: Students are working on their own. I will be assisting students with different processes as they arise. Will give a demonstration on planning lumber down after glued together.
FRIDAY 2/11/11
Pd. 4,5 Plastics: Students will be designing there next project which will be the Clip board.
Pd. 2,3,6 Basic Wood Work: Students will continue to work on projects. When special operations are needed we will stop working and give a demonstration on that operation.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects. When special operations are needed we will stop working and give a demonstration on that operation.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz.
Monday, January 31, 2011
LESSON PLAN
Kevin Scheib (Wood Shop) weekly lesson plans (1/31/2011-2/4/2011)22 th week
Monday 1/31/11 Lessons Are Pushed Back One Day due to My Absence
Pd. 4,5 Plastics: Students will be sanding projects on one side and then we will be cutting them to the correct size.
Pd. 2,3,6 Basic Wood Working : Students will be starting their own individual projects today.
Pd. 7 Advanced Cabinet Making: Students will be starting their own individual projects today.
TUESDAY 2/1/11
Pd. 4,5 Plastics: Students will be given demo on the proper steps to sanding . They will go through three different steps. I will then give a demo on buffing the project.
Pd. 2,3,6 Basic Wood Working: Students will continue planning lumber and starting to layout cutting patterns.
Pd. 7 Advanced Cabinet Making: Advanced students will continue to work on projects and basic wood work will continue planning lumber and starting to layout cutting patterns.
WENDNESDAY 2/2/11
Pd. 4,5 Plastics: Students will continue with sanding and buffing..
Pd. 2,3,6 BASIC WOOD WORKING: Students will continue layout and cutting of their first project pieces.
Pd. 7 Advanced Cabinet Making: Students will continue layout and cutting of their first project pieces. Advanced students continue to work on projects.
THURSDAY 2/3/11
Pd. 4,5 Plastics: Students will be finishing buffing.
Pd. 2,3,6 Basic Wood Working: Students are working on their own. I will be assisting students with different processes as they arise.
Pd.7 Advanced Cabinet Making: Students are working on their own. I will be assisting students with different processes as they arise.
FRIDAY 2/4/11
Pd. 4,5 Plastics: I Will give demo on laying out of the two holes that will be drilled into the bottom to hold the salt and pepper.
Pd. 2,3,6 Basic Wood Work: Students will continue to work on projects. When special operations are needed we will stop working and give a demonstration on that operation.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects. When special operations are needed we will stop working and give a demonstration on that operation.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz.
Kevin Scheib (Wood Shop) weekly lesson plans (1/31/2011-2/4/2011)22 th week
Monday 1/31/11 Lessons Are Pushed Back One Day due to My Absence
Pd. 4,5 Plastics: Students will be sanding projects on one side and then we will be cutting them to the correct size.
Pd. 2,3,6 Basic Wood Working : Students will be starting their own individual projects today.
Pd. 7 Advanced Cabinet Making: Students will be starting their own individual projects today.
TUESDAY 2/1/11
Pd. 4,5 Plastics: Students will be given demo on the proper steps to sanding . They will go through three different steps. I will then give a demo on buffing the project.
Pd. 2,3,6 Basic Wood Working: Students will continue planning lumber and starting to layout cutting patterns.
Pd. 7 Advanced Cabinet Making: Advanced students will continue to work on projects and basic wood work will continue planning lumber and starting to layout cutting patterns.
WENDNESDAY 2/2/11
Pd. 4,5 Plastics: Students will continue with sanding and buffing..
Pd. 2,3,6 BASIC WOOD WORKING: Students will continue layout and cutting of their first project pieces.
Pd. 7 Advanced Cabinet Making: Students will continue layout and cutting of their first project pieces. Advanced students continue to work on projects.
THURSDAY 2/3/11
Pd. 4,5 Plastics: Students will be finishing buffing.
Pd. 2,3,6 Basic Wood Working: Students are working on their own. I will be assisting students with different processes as they arise.
Pd.7 Advanced Cabinet Making: Students are working on their own. I will be assisting students with different processes as they arise.
FRIDAY 2/4/11
Pd. 4,5 Plastics: I Will give demo on laying out of the two holes that will be drilled into the bottom to hold the salt and pepper.
Pd. 2,3,6 Basic Wood Work: Students will continue to work on projects. When special operations are needed we will stop working and give a demonstration on that operation.
Pd. 7 Advanced Cabinet Making: Students will continue to work on projects. When special operations are needed we will stop working and give a demonstration on that operation.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz.
Monday, January 3, 2011
LESSON PLAN
Kevin Scheib (Wood Shop) weekly lesson plans (1/3/2011-1/7/2011)18th week
Monday 1/3/11
Pd. 4,5 Plastics: Will continue with pouring of chess pieces and sand blasting. Some students will be pouring the second colored pieces.
Pd. 2,3,6 Basic Wood Working : Will give demonstration on using the router and the template for engraving names.
Pd. 7 Advanced Cabinet Making: Will give demonstration on using the router and the template for engraving names. Advanced students will be working on their projects. Many advanced students are finishing the first projects.
TUESDAY 1/4/11
Pd. 4,5 Plastics: Will continue with chess project. Students will also be working on the board for the project.
Pd. 2,3,6 Basic Wood Working: Students will be working on the engraving project. We will also be picking the projects that they will be doing on their own. We will do this as a class.
Pd. 7 Advanced Cabinet Making: Students will be working on the engraving project. We will also be picking the projects that they will be doing on their own. We will do this as a class.
WENDNESDAY 1/5/11
Pd. 4,5 Plastics: Will continue with chess project. Students will also be working on the board for the project.
Pd. 2,3,6 Basic Woodworking: Students will be working on the engraving project. This will take approximately four days till everyone is done. Some students will be choosing projects.
Pd. 7 Advanced Cabinet Making: Basic students in this class will be finishing the engraving project. Students will then be starting the projects they have picked on their own.
THURSDAY 1/6/11
Pd. 4,5 Plastics: Students will be spraying the chess pieces with a clear acrylic spray. At this point students will be done with this project.
Pd. 2,3,6 Basic Wood Working: Students will be starting new projects.
Pd.7 Advanced Cabinet Making: Students will be starting new projects.
FRIDAY 1/7/11
Pd. 4,5 Plastics: Any students who are not done with the chess project will be finishing up. Other students will be preparing materials for the next project.
Pd. 2,3,6 Basic Wood Work: Students will continue with working their own individual projects. Things will progress at a little slower progress till students on done with planning of lumber.
Pd. 7 Advanced Cabinet Making: Students will continue with working their own individual projects. Things will progress at a little slower progress till students on done with planning of lumber.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz.
Kevin Scheib (Wood Shop) weekly lesson plans (1/3/2011-1/7/2011)18th week
Monday 1/3/11
Pd. 4,5 Plastics: Will continue with pouring of chess pieces and sand blasting. Some students will be pouring the second colored pieces.
Pd. 2,3,6 Basic Wood Working : Will give demonstration on using the router and the template for engraving names.
Pd. 7 Advanced Cabinet Making: Will give demonstration on using the router and the template for engraving names. Advanced students will be working on their projects. Many advanced students are finishing the first projects.
TUESDAY 1/4/11
Pd. 4,5 Plastics: Will continue with chess project. Students will also be working on the board for the project.
Pd. 2,3,6 Basic Wood Working: Students will be working on the engraving project. We will also be picking the projects that they will be doing on their own. We will do this as a class.
Pd. 7 Advanced Cabinet Making: Students will be working on the engraving project. We will also be picking the projects that they will be doing on their own. We will do this as a class.
WENDNESDAY 1/5/11
Pd. 4,5 Plastics: Will continue with chess project. Students will also be working on the board for the project.
Pd. 2,3,6 Basic Woodworking: Students will be working on the engraving project. This will take approximately four days till everyone is done. Some students will be choosing projects.
Pd. 7 Advanced Cabinet Making: Basic students in this class will be finishing the engraving project. Students will then be starting the projects they have picked on their own.
THURSDAY 1/6/11
Pd. 4,5 Plastics: Students will be spraying the chess pieces with a clear acrylic spray. At this point students will be done with this project.
Pd. 2,3,6 Basic Wood Working: Students will be starting new projects.
Pd.7 Advanced Cabinet Making: Students will be starting new projects.
FRIDAY 1/7/11
Pd. 4,5 Plastics: Any students who are not done with the chess project will be finishing up. Other students will be preparing materials for the next project.
Pd. 2,3,6 Basic Wood Work: Students will continue with working their own individual projects. Things will progress at a little slower progress till students on done with planning of lumber.
Pd. 7 Advanced Cabinet Making: Students will continue with working their own individual projects. Things will progress at a little slower progress till students on done with planning of lumber.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz.
Subscribe to:
Posts (Atom)