Monday, December 20, 2010

LESSON PLAN
Kevin Scheib (Wood Shop) weekly lesson plans (12/20/10 - 12/24/10)17th week
Monday 12/20/10

Pd. 4,5 Plastics: Will continue with pouring of chess pieces and sand blasting.

Pd. 2,3,6 Basic Wood Working : Will be Finishing clock (adding plexi glass to front) .

Pd. 7 Advanced Cabinet Making: Will be Finishing clocks (adding plexi glass to front).
TUESDAY 12/21/10

Pd. 4,5 Plastics: Shop clean up for Holidays

Pd. 2,3,6 Basic Wood Working: Shop clean up for holidays

Pd. 7 Advanced Cabinet Making: Shop clean up for Holidays

WENDNESDAY 12/22/10 (Will be going to the gym with kids)

Pd. 4,5 Plastics:

Pd. 2,3,6 Basic Woodworking:

Pd. 7 Advanced Cabinet Making:
THURSDAY 12/23/10 EARLY DISSMISAL
Pd. 4,5 Plastics: Finishing up on anything for anyone who is behind

Pd. 2,3,6 Basic Wood Working: Finishing up on anything for anyone who is behind

Pd.7 Advanced Cabinet Making: Finishing up on anything for anyone who is behind
FRIDAY12/24/10 NO SCHOOL

Pd. 4,5 Plastics:

Pd. 2,3,6 Basic Wood Work:

Pd. 7 Advanced Cabinet Making:
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz.

Monday, December 6, 2010

LESSON PLAN
Kevin Scheib (Wood Shop) weekly lesson plans (11/6/10 - 12/10/10)15th week
Monday 12/6/10 No School

Pd. 4,5 Plastics: Students will apply last coat of latex to the molds for the chess pieces. Any student not done with the mug projects will finish that while latex is drying.

Pd. 2,3,6 Basic Wood Working : Students will be sanding and routering the clock pieces and preparing them for assembly.
Pd. 7 Advanced Cabinet Making: Students will be sanding and routering the clock pieces and preparing them for assembly. Advanced students will continue to work on projects.
TUESDAY 12/7/10

Pd. 4,5 Plastics: Students will start to remove chess pieces from the latex. We will use baby powder so mold does not stick to self. I will also give demonstration on laying out the chess board. We will use a 8” X 8” acrylic sheet.
Pd. 2,3,6 Basic Wood Working: Students will continue to sand using electric sanders but they will also be hand sanding certain parts of the clock parts.
Pd. 7 Advanced Cabinet Making: Students will continue to sand using electric sanders but they will also be hand sanding certain parts of the clock parts. Many Advanced students or assembling and nearing completion of first projects.
WENDNESDAY 12/8/10

Pd. 4,5 Plastics: Students will continue with removal of chess pieces from molds and layout of board.

Pd. 2,3,6 Basic: I will be giving a demonstration on assembly using the air nail gun and glue.

Pd. 7 Advanced Cabinet Making: I will be giving a demonstration on assembly using the air nail gun and glue. Advanced students continue to work on projects.
THURSDAY 12/9/10 TURKEY DAY

Pd. 4,5 Plastics: Will give demonstration on sand blasting of board to create pattern on board.

Pd. 2,3,6 Basic Wood Working: Students will start to assemble clocks. I will be giving very close supervision because students will be use the air nail gun. Students will be warned they must have safety glasses on or the will be written up.

Pd.7 Advanced Cabinet Making: Students will start to assemble clocks. I will be giving very close supervision because students will be use the air nail gun. Students will be warned they must have safety glasses on or the will be written up.
FRIDAY12/10/10 NO SCHOOL

Pd. 4,5 Plastics: Will give demonstration on mixing of clear acrylic and how to add dye to mixture.

Pd. 2,3,6 Basic Wood Work: Students will continue with assembly of clocks.

Pd. 7 Advanced Cabinet Making: Students will continue with assembly of clocks. Advanced students continue to work on projects.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz.

Monday, November 8, 2010

LESSON PLAN
Kevin Scheib (Wood Shop) weekly lesson plans (11/8/10 - 11/12 /10)11th week
Monday 11/8/10
Pd. 4,5 Plastics: We will be starting the casting project. I will be giving a demonstration on how we will be making the molds for the chess pieces that we will be making. We will be using Latex mold builder.
Pd. 2,3,6 Basic Wood Working : Some students will be finishing the sanding and routering and some will be assembling the shelf. We will be using 1 ½” finish nails glue and hammers.
Pd. 7 Advanced Cabinet Making: Some students will be finishing the sanding and routering and some will be assembling the shelf. We will be using 1 ½” finish nails glue and hammers.
TUESDAY 11/9/10

Pd. 4,5 Plastics: We will continue with the mold building process.
Pd. 2,3,6 Basic Wood Working: Students will continue with shelf assembly. Will give demonstration on how to drill and apply the three pegs to the shelf
Pd. 7 Advanced Cabinet Making: Students will continue with shelf assembly. Will give demonstration on how to drill and apply the three pegs to the shelf. Advanced students will continue with advanced projects.
WENDNESDAY 11/10/10

Pd. 4,5 Plastics: Will continue with mold project.
Pd. 2,3,6 Basic Wood Working: Students will continue with shelf assembly. Will give demonstration on how to drill and apply the three pegs to the shelf
Pd. 7 Advanced Cabinet Making: Students will continue with shelf assembly. Will give demonstration on how to drill and apply the three pegs to the shelf. Advanced students will continue with advanced projects.
THURSDAY 11/11/10

Pd. 4,5 Plastics: Students will peel Latex molds off the forms.

Pd. 2,3,6 Basic Wood Working: Students will sand putty off nail holes and prepare for staining. Some students will start to stain.
Pd.7 Advanced Cabinet Making: Students will sand putty off nail holes and prepare for staining. Some students will start to stain.
FRIDAY 11/12/10

Pd. 4,5 Plastics: Some students may still be removing the forms from the molds. Will give demonstration on mixing and poring the molds.
Pd. 2,3,6 Basic Wood Working: Will give a demonstration on the wood lathe. All students will be required to make a project on the lathe.
Pd. 7 Advanced Cabinet Making: Will give a demonstration on the wood lathe. All students will be required to make a project on the lathe.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz.

Tuesday, November 2, 2010

LESSON PLAN
Kevin Scheib (Wood Shop) weekly lesson plans (11/1/10 - 11/5 /10)10th week
Monday 11/1/10
Pd. 4,5 Plastics: Some students are finish the candy dish made by the blow mold method. This is the last day we will be working on this project.
Pd. 2,3,6 Basic Wood Working : Students will start to cut parts for the shelf. They will cut the back first then the tops. Students will then cut one piece to use for the self supports.
Pd. 7 Advanced Cabinet Making: Students will start to cut parts for the shelf. They will cut the back first then the tops. Students will then cut one piece to use for the self supports. Advanced students will continue work on their projects.
TUESDAY 11/2/10

Pd. 4,5 Plastics: We are going to start the soft plastic injection project. We will be using the hot plate to heat the material to 350 degrees. Extreme caution must be taking. I will give demo on the process.
Pd. 2,3,6 Basic Wood Working: Students will be given a hand out on different types of joints that will be used in all different kinds of projects.
Pd. 7 Advanced Cabinet Making: Students will be given a hand out on different types of joints that will be used in all different kinds of projects.
WENDNESDAY 11/3/10

Pd. 4,5 Plastics: Students will be working on the soft plastic project. They will make many different objects of their chose.
Pd. 2,3,6 Basic Wood Working: Students will be given a test on different types of Joints. Students will continue to work on the shelf projects.
Pd. 7 Advanced Cabinet Making: Students will be given a test on different types of Joints. Students will continue to work on the shelf projects.
THURSDAY 11/4/10

Pd. 4,5 Plastics: Students will be working on the soft plastic project. They will make many different objects of their chose.
Pd. 2,3,6 Basic Wood Working: Students will continue to work on shelf project. They will be using the band saw, oscillating sander, disc Sander, and the hand palm sanders
Pd.7 Advanced Cabinet Making: Students will continue to work on shelf project. They will be using the band saw, oscillating sander, disc Sander, and the hand palm sanders
FRIDAY 11/5/10

Pd. 4,5 Plastics: Students will be working on the soft plastic project. They will make many different objects of their chose.
Pd. 2,3,6 Basic Wood Working: Will give a demonstration on assembling the shelf using glue, nails, and the 12 oz. hammer.
Pd. 7 Advanced Cabinet Making: Will give a demonstration on assembling the shelf using glue, nails, and the 12 oz. hammer.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz.

Monday, October 25, 2010

LESSON PLAN
Kevin Scheib (Wood Shop) weekly lesson plans (10/25/10 - 10/29 /10)7th week
Monday 10/25
Pd. 4,5 Plastics: We will start blow molding Projects(cereal bowl). I will give demonstration on peeling the protective coating off precut acrylic then place in the oven for 4 minutes. We will then take out and place mold blower. After bowl is shaped I will cut shape out on band saw. I will then sand the edge. I will then buff the edge.
Pd. 2,3,6 Basic Wood Working : Students will start clear coating,. I will give a demo on how to sand the first coat to take all the dust out of the finish. Students will then wipe it down with tack cloth then apply second coat.
Pd. 7 Advanced Cabinet Making: Students will start clear coating. I will give a demo on how to sand the first coat to take all the dust out of the finish. Students will then wipe it down with tack cloth then apply second coat.
TUESDAY 10/26

Pd. 4,5 Plastics: Students will choose their color and then they will take turns doing project. Some students may do submersion projects also.
Pd. 2,3,6 Basic Wood Working: Students will continue to apply clear coat. Students will apply three coats in all.

Pd. 7 Advanced Cabinet Making: Students will continue to apply clear coat. Students will apply three coats in all.
WENDNESDAY 10/27

Pd. 4,5 Plastics: We will continue with blow mold project.

Pd. 2,3,6 Basic Wood Working: Students will be finishing up the clear cutting. I will grade finished projects so students may take them home.
Pd. 7 Advanced Cabinet Making: Students will be finishing up the clear cutting. I will grade finished projects so students may take them home.
THURSDAY 10/28

Pd. 4,5 Plastics: Will continue with the blow project.

Pd. 2,3,6 Basic Wood Working: Students who were absent will finish clear coating. We will be discussing different types of joints used in wood project construction.
Pd. 7 Advanced Cabinet Making: Students who were absent will finish clear coating. We will be discussing different types of joints used in wood project construction.
FRIDAY 10/29

Pd. 4,5 Plastics: WE will be starting a lager blow mold project (large candy dish).

Pd. 2,3,6 Basic Wood Working: We will be starting the next project which will be the shelf with pegs. Students will start planning lumber down.
Pd. 7 Advanced Cabinet Making: We will be starting the next project which will be the shelf with pegs. Students will start planning lumber down.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz.

Monday, October 18, 2010

LESSON PLAN
Kevin Scheib (Wood Shop) weekly lesson plans (10/18/10 - 10/122 /10)7th week
Monday 10/18

Pd. 4,5 Plastics: We will be wrapping up the submersion projects today.

Pd. 2,3,6 Basic Wood Working : Students will continue to assemble and apply the screws to projects. Students will continue to put plugs into project, and fill holes. Some students will start to remove plugs and sand.
Pd. 7 Advanced Cabinet Making: Students will continue to assemble and apply the screws to projects. Students will continue to put plugs into project, and fill holes. Some students will start to remove plugs and sand. Advanced students will continue with projects.
TUESDAY 10/19

Pd. 4,5 Plastics: We will be starting they Soft plastics projects. I will give a demonstration on the process of making soft artificial lures.
Pd. 2,3,6 Basic Wood Working: Students will continue with bench projects. I will be giving a staining demonstration.

Pd. 7 Advanced Cabinet Making: Students will continue with bench projects. I will be giving a staining demonstration.
WENDNESDAY 10/20

Pd. 4,5 Plastics: Students will start the soft plastics project. Students will be allowed to choose any mold they like. They may do as many as they like as long as everyone does the project first.

Pd. 2,3,6 Basic Wood Working: Some students will start staining while others will be cutting plugs and sanding.

Pd. 7 Advanced Cabinet Making: Some students will start staining while others will be cutting plugs and sanding.

THURSDAY 10/21

Pd. 4,5 Plastics: Will continue with the soft plastics project.

Pd. 2,3,6 Basic Wood Working: Most student will be staining today.

Pd. 7 Advanced Cabinet Making: : Most student will be staining today.

FRIDAY 10/22

Pd. 4,5 Plastics: We will be wrapping up the soft plastics projects today.

Pd. 2,3,6 Basic Wood Working: Students will be finish up staining. I will give a demonstration on clear coating.

Pd. 7 Advanced Cabinet Making: Students will be finish up staining. I will give a demonstration on clear coating.

FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz.

Thursday, October 7, 2010

LESSON PLAN
Kevin Scheib (Wood Shop) weekly lesson plans (10/11/10 - 10/15 /10)7th week
Monday 10/11 In-service

Pd. 4,5 Plastics:

Pd. 2,3,6 Basic Wood Working :

Pd. 7 Advanced Cabinet Making:

TUESDAY 10/12 Act 80 Day

Pd. 4,5 Plastics:

Pd. 2,3,6 Basic Wood Working:

Pd. 7 Advanced Cabinet Making:

WENDNESDAY 10/13

Pd. 4,5 Plastics: Will be giving a demonstration on submersion molding. Students will be making coin purses.

Pd. 2,3,6 Basic Wood Working: Will give demonstration on assembly of the stool. Will be using a jig, air nail guns, and power drills.
Pd. 7 Advanced Cabinet Making: Will give demonstration on assembly of the stool. Will be using a jig, air nail guns, and power drills.
THURSDAY 10/14

Pd. 4,5 Plastics: Students will be working on the submersion project.

Pd. 2,3,6 Basic Wood Working: Students will start to put projects together. They will use the air nil gun first then they will use screws to finish assembly. Students will cut wooden plugs to fill screw holes.
Pd. 7 Advanced Cabinet Making: : Students will start to put projects together. They will use the air nil gun first then they will use screws to finish assembly. Students will cut wooden plugs to fill screw holes.
FRIDAY 10/15

Pd. 4,5 Plastics: Students will continue to work on the submersion projects.

Pd. 2,3,6 Basic Wood Working: Students will continue with assembly.

Pd. 7 Advanced Cabinet Making: Students will continue with assembly. Advanced students will continue to prepare wood for their projects.

FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz.

Monday, September 27, 2010

LESSON PLAN
Kevin Scheib (Wood Shop) weekly lesson plans (9/27/10 - 10/1 /10)5th week
Monday 9/27

Pd. 4,5 Plastics: Students will be working on the Laminated plastic key chain project. Students will sand all edges on belt sander then use hand sand Paper. Students will then buff the edges.

Pd. 2,3,6 Basic Wood Working : We will start first project by selecting the boards to make the bench. We will then start to plane lumber down.
Pd. 7 Advanced Cabinet Making: We will start first project by selecting the boards to make the bench. We will then start to plane lumber down. Advanced students will be choosing projects and working on plans and the plan the steps they need to follow.
TUESDAY 9/28

Pd. 4,5 Plastics: Students will continue with key chain project. I will give a demo on drilling and adding the key holder.

Pd. 2,3,6 Basic Wood Working: We will finish up the planning of wood. We will then cut into individual pieces for each student.
Pd. 7 Advanced Cabinet Making: We will finish up the planning of wood. We will then cut into individual pieces for each student.
WENDNESDAY 9/29

Pd. 4,5 Plastics: Students will finish up key chain project.

Pd. 2,3,6 Basic Wood Working: Students will follow my lead as we go through the steps to prepare the wood into separate pieces of wood.
Pd. 7 Advanced Cabinet Making: Students will follow my lead as we go through the steps to prepare the wood into separate pieces of wood.
THURSDAY 9/30

Pd. 4,5 Plastics: I will give a demonstration on the start of our next project which will be the clip board. We will be using acrylic glass and Resin to create this project. We will add a picture between the acrylic and resin.
Pd. 2,3,6 Basic Wood Working: We will cut the angle cut to the top and bottom of the bench ends.

Pd. 7 Advanced Cabinet Making: We will cut the angle cut to the top and bottom of the bench ends. Advanced students will be starting projects.
FRIDAY 10/1

Pd. 4,5 Plastics: Students will start project by cutting acrylic and sanding the edges.

Pd. 2,3,6 Basic Wood Working: Will give students a demonstration on pattern layout and then how to cut the ends out on the band saw.
Pd. 7 Advanced Cabinet Making: Will give students a demonstration on pattern layout and then how to cut the ends out on the band saw.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz.

Monday, September 20, 2010

LESSON PLAN
Kevin Scheib (Wood Shop) weekly lesson plans (9-20-2010/9-27-10)4th week
Monday 9/13

Pd. 4,5 Plastics: We will begin first project. I will give demonstration on layout and cutting of plastic to make refrigerator magnetic photo frame We will sand all edges with 280 grit and 600 grit.
Pd. 2,3,6 Basic Wood Working : Will give students 5 minutes to look over study sheet and then will give the quiz on the Circular saw and the Radial Arm Saw. If time allows we will start to go over the Band Saw.
Pd. 7 Advanced Cabinet Making: Will give students 5 minutes to look over study sheet and then will give the quiz on the Circular Saw and the Radial arm Saw. If time allows we will start to go over the Band Saw.
TUESDAY 9/14

Pd. 4,5 Plastics: I will give a demonstration on buffing the edges to make the edges clear. I will then demonstrate how to heat the plastic using the rod heater. We will then bend over to form the picture holder.
Pd. 2,3,6 Basic Wood Working: Will give demonstration on the Band Saw. If time allows we will move on to the Drill Press.
Pd. 7 Advanced Cabinet Making: Will give demonstration on the Band Saw. If time allows we will move on to the Drill Press.
WENDNESDAY 9/15

Pd. 4,5 Plastics: Students will finish up the small picture frame. Will give Demo on making a standalone clear frame for a 3.5 x 5 picture holder.
Pd. 2,3,6 Basic Wood Working: Will finish the demonstration on the drill press. Will give demonstration on the Disc and Belt Sander.
Pd. 7 Advanced Cabinet Making: Will finish the demonstration on the drill press. Will give demonstration on the Disc and Belt Sander.
THURSDAY 9/16

Pd. 4,5 Plastics: Students will work on frame project. Students may take home when done with project

Pd. 2,3,6 Basic Wood Working: Will give students 5 minutes to look the Band Saw on Drill Press study guides and then will give the test. They will have the rest of the period to complete the test.
Pd. 7 Advanced Cabinet Making: Will give students 5 minutes to look the Band Saw on Drill Press study guides and then will give the test. They will have the rest of the period to complete the test.
FRIDAY 9/17

Pd. 4,5 Plastics: Will give demo on Dice project . Students will cut a one inch cube from long strips of 1” thick acrylic. Students use radial arm saw. Will demo the sanding process which starts with the disc sander and then hand sand paper.

Pd. 2,3,6 Basic Wood Working: Will give demonstration on using the Power miter saw.

Pd. 7 Advanced Cabinet Making: Will give demonstration on using the Power miter saw.

FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz.
LESSON PLAN
Kevin Scheib (Wood Shop) weekly lesson plans (9-13-2010/9-17-10)4th week
Monday 9/13

Pd. 4,5 Plastics: We will begin first project. I will give demonstration on layout and cutting of plastic to make refrigerator magnetic photo frame We will sand all edges with 280 grit and 600 grit.
Pd. 2,3,6 Basic Wood Working : Will give students 5 minutes to look over study sheet and then will give the quiz on the Circular saw and the Radial Arm Saw. If time allows we will start to go over the Band Saw.
Pd. 7 Advanced Cabinet Making: Will give students 5 minutes to look over study sheet and then will give the quiz on the Circular Saw and the Radial arm Saw. If time allows we will start to go over the Band Saw.
TUESDAY 9/14

Pd. 4,5 Plastics: I will give a demonstration on buffing the edges to make the edges clear. I will then demonstrate how to heat the plastic using the rod heater. We will then bend over to form the picture holder.
Pd. 2,3,6 Basic Wood Working: Will give demonstration on the Band Saw. If time allows we will move on to the Drill Press.
Pd. 7 Advanced Cabinet Making: Will give demonstration on the Band Saw. If time allows we will move on to the Drill Press.
WENDNESDAY 9/15

Pd. 4,5 Plastics: Students will finish up the small picture frame. Will give Demo on making a standalone clear frame for a 3.5 x 5 picture holder.
Pd. 2,3,6 Basic Wood Working: Will finish the demonstration on the drill press. Will give demonstration on the Disc and Belt Sander.
Pd. 7 Advanced Cabinet Making: Will finish the demonstration on the drill press. Will give demonstration on the Disc and Belt Sander.
THURSDAY 9/16

Pd. 4,5 Plastics: Students will work on frame project. Students may take home when done with project

Pd. 2,3,6 Basic Wood Working: Will give students 5 minutes to look the Band Saw on Drill Press study guides and then will give the test. They will have the rest of the period to complete the test.
Pd. 7 Advanced Cabinet Making: Will give students 5 minutes to look the Band Saw on Drill Press study guides and then will give the test. They will have the rest of the period to complete the test.
FRIDAY 9/17

Pd. 4,5 Plastics: Will give demo on Dice project . Students will cut a one inch cube from long strips of 1” thick acrylic. Students use radial arm saw. Will demo the sanding process which starts with the disc sander and then hand sand paper.

Pd. 2,3,6 Basic Wood Working: Will give demonstration on using the Power miter saw.

Pd. 7 Advanced Cabinet Making: Will give demonstration on using the Power miter saw.

FOR ALL PERIODS:
PA. Standards (Science & Technology); 2.1, 2.2, 2.3, 3.2, 3.4, 3.6
Objectives; Wood shop-To have students fully understand the safe and proper use of all power equipment in the shop.
Plastics- To give students an understanding of how signs are engraved, and how plastic can be heated and shaped
Assessments; Will be done by Question and Answers and Quiz.

Monday, September 13, 2010

LESSON PLAN
Kevin Scheib (Wood Shop) 3rd week of school (9/13/2010-9/17/2010)
Monday 9/13/10

Pd. 2,3,6 Basic Wood: We will start going over power equipment in the shop. We will be starting with the Planer and the Jointer. All students will receive a packet with all the equipment of the shop they will be working with.
Pd.4,5 Plastics: Students will continue with the sanding of the edges of the piece of acrylic they received Friday. They will then buff the edges the same as the demonstration.
Pd.7 Advanced Cabinet Making: We will start going over power equipment in the shop. We will be starting with the Planer and the Jointer. All students will receive a packet with all the equipment of the shop they will be working with.
TUESDAY 9/14/10

Pd. 2,3,6 Basic Wood: We will continue with the demonstrations of the Planer and Jointer.

Pd.4,5 Plastics: I will give a demonstration on marking the acrylic and then demo how we will heat it so that it can be folded over to make a small picture frame.
Pd.7 Advanced Cabinet Making: We will continue with the demonstrations of the Planer and Jointer.

WENDNESDAY 9/15/10

Pd. 2,3,6 Basic Wood: Students will be given a quiz on both pieces of equipment. It will be True and False and part identification.
Pd.4,5 Plastics: We will cut magnetic stripping and adhere it to the back of frame so it can me hung on the refrigerator.

Pd.7 Advanced Cabinet Making: Students will be given a quiz on both pieces of equipment. It will be True and False and part identification.
THURSDAY 9/16/10

Pd. 2,3,6 Basic Wood: I will give a demonstration on the Table saw. This will take most of the period.

Pd.4,5 Plastics: We will cut out the acrylic for the next size picture frame and perform the sanding and buffing operations.
Pd.7 Advanced Cabinet Making: I will give a demonstration on the Table saw. This will take most of the period.

FRIDAY 9/17/10

Pd. 2,3,6 Basic Wood: Students will be given a quiz on the Table Saw. When everyone is done I will give a demonstration on the Radial Arm saw.
Pd.4,5 Plastics: I will give a demonstration on heating and bending of acrylic in two positions so it can stand on its own.

Pd.7 Advanced Cabinet Making: Students will be given a quiz on the Table Saw. When everyone is done I will give a demonstration on the Radial Arm saw.
FOR ALL PERIODS:
PA. Standards (Science & Technology); 13.1.5, 13.1.8, 13.1.11, 13.2.8, 13.2.11, 13.3.5, 13.3.8,13.4.5, 13.4.8, 13.4.11
Objectives; Wood shop- To give the students a full understanding the importance of how to use machines in a safe way to produce a project that can be used every day life
Plastics- To give students an understanding of how industry produces products made of plastic that we use every day.
Assessments; Will be done by class performance and by project evaluation.

Friday, August 27, 2010

This Blog is for the week of 8/30/2010 to 9/3/2010

Hello every one! students and parents. I hope every one had a good summer vacation!
The first week of class we will be doing introductions to the wood shop. I will be letting students know what is expected from them and how things will be run in the shop. The shop is a grate place for students to work with skills that they normally don't get to work with. Many projects are built in this shop and I hope students will take advantage of the time they have in here.

If parents have any questions for me you can contact me through the high school office or by email on the schools web site.

I will have more informitive blogs to come

Thank You
Mr Scheib

Monday, May 17, 2010

This Post Is For the Week Of (5/17/2010 to 5/21/2010)

Wood Shop-Students are continuing to work on projects. Many nice projects are being finished. Time is of the essences for finishing projects. I would like for students to pay for projects as soon as possible. Students will have approximately 10 days of work time left. Seniors will only have approximately 5 days of work time left. We will be cleaning the shop the last week of school.

Plastics Class- Students are finishing up the chess board projects. We sand blasted the boards on Friday and students are sanding the bases of the chess pieces. They came out very good.

There are no home work assignments at the present time.

Monday, May 10, 2010

This Post Is For the Week Of (5/10/2010 to 5/11/2010)

Wood Shop-Students are continuing to work on projects. Many nice projects are being finished. Time is of the essences for finishing projects. I would like for students to pay for projects as soon as possible. Students will have approximately 15 days of work time left. Seniors will only have approximately 10 days of work left. We will be cleaning the shop the last week of school.

Plastics Class- Students are in the process of poring their chess sets. We are using clear polyester resin. Students are adding dyes to the resin to make different colors. We will be making the boards from plastic also.

There are no home work assignments at the present time.

Tuesday, May 4, 2010

This Post Is For the Week Of (4/26/2010 to 4/30/2010)

Wood Shop-Students are continuing to work on projects. Many nice projects are being finished. Time is of the essences for finishing projects. I would like for students to pay for projects as soon as possible.

Plastics Class- Students are in the process of poring their chess sets. We are using clear polyester resin. Students are adding dyes to the resin to make different colors. We will be making the boards from plastic also.

There are no home work assignments at the present time.

Monday, April 26, 2010

This Post Is For the Week Of (4/26/2010 to 4/30/2010)

Wood Shop-Students will continue to work on individual projects. Students are presently still taking PSSA test. Some classes are shortened. Many Students are finishing projects. I would like for students to pay for projects as soon as possible.

Plastics Class- Students are in the process of poring their chess sets. We are using clear polyester resin. Students are adding dyes to the resin to make different colors. We will be making the boards from plastic also.

There are no home work assignments at the present time.

Monday, April 19, 2010

This Post Is For the Week Of (4/19/2010 to 4/23/2010)

Wood Shop-Students will continue to work on individual projects. The fourth marking period will be very busy for students as far taking many test so we need to take advantage of the time they will have in wood shop.Many Students are finishing projects. I would like for students to pay for projects as soon as possible.

Plastics Class- Students are in the process of poring their chess sets. We are using clear polyester resin. Students are adding dyes to the resin to make different colors. We will be making the boards from plastic also.

There are no home work assignments at the present time.

Monday, April 12, 2010

This Post Is For the Week Of (4/12/2010 to 4/16/2010)

Wood Shop-Students will continue to work on individual projects. The fourth marking period will be very busy for students as far taking many test so we need to take advantage of the time they will have in wood shop.Many Students are finishing projects. I would like for students to pay for projects as soon as possible.Class periods will be shorted on 4/14 and 15 due to PSSA testing.

Plastics Class- Students will be making chess sets from resin. They will be making molds from chess pieces using latex mold builder.

There are no home work assignments at the present time. Class periods will be shortened on 4/14 and 15 due to PSSA testing.

Monday, April 5, 2010

This Post Is For the Week Of (4/5/2010 to 4/9/2010)

Wood Shop-Students will continue to work on individual projects. The fourth marking period will be very busy for students as far taking many test so we need to take advantage of the time they will have in wood shop.Many Students are finishing projects. I would like for students to pay for projects as soon as possible.

Plastics Class- Students will be making chess sets from resin. They will be making molds from chess pieces using latex mold builder.

There are no home work assignments at the present time.

Monday, March 29, 2010

This Post Is For the Week Of (3/29/2010 to 4/1/2010)

Wood Shop-Students will continue to work on individual projects. We are closing in on the end of the third marking period very quickly. Thursday is the start of the fourth marking pi rod.Many students are finishing up projects. I would like if students could pay for their projects upon completion and they will be aloud to take their project home. I am very Happy with the quality of work being done. The fourth marking period will be very busy for students as far taking many test so we need to take advantage of the time they will have in wood shop.

Plastics Class- On Friday March 26 We set sail with the canoe in the pool here at school. It was very successful. The students had a lot of fun with it. This was a project that students could do at home with materials they could purchase at the local Lowe's or home Depot and the local auto parts store. The cost of the materials was approximately $250.00.
We will be starting individual projects this week.

There are no home work assignments at the present time.

Monday, March 22, 2010

This post is for the week of (March 22 to March 26, 2010)

Wood Shop
-Students will continue to work on individual projects. We are closing in on the end of the third marking period very quickly. Many students are finishing up projects. I would like if students could pay for their projects upon completion and they will be aloud to take their project home. I am very Happy with the quality of work being done. The fourth marking period will be very busy for students as far taking many test so we need to take advantage of the time they will have in wood shop.

Plastics Class

- Students will be finishing up the canoe this week. We must put the end caps on top and the side tops on. We will paint the out side white and the inside will be gray. We will be taking the canoe to the pool on Friday. Students are to bring in shorts or swim suet's for Friday. The boat will be on display in the High School lobby next week if permitted.

There is no home work at the present time.

Thursday, March 4, 2010

This post is for the week of (3/1/2010 - 3/5/2010)

Students will not have school on3/1/2010 It is a Act 80 Day

Wood shop Students
Many students are finishing projects and starting on their third or forth projects. I am very pleased with the quality of work that is being done. Students are showing grate pride in there work.At the present time we do not have any home work assignments.

Plastics Tech.
Students at the present time students are working on the class project. We are building a canoe. Students are learning how to work with fiber class. Students are having a good time and are looking forward to the end of the the project so we can take it out and try it out.

At the present time we do not have any home work assignments.

Monday, February 22, 2010

This post is for the week of (2/22/2010 to 2/26/2010)

Wood shop Students
Many students are finishing projects and starting on their third or forth projects. I am very pleased with the quality of work that is being done. Students are showing grate pride in there work.

At the present time we do not have any home work assignments.

Plastics Tech. students
At the present time students are working on the class project. We are building a canoe. Students are learning how to work with fiber class. Students are having a good time and are looking forward to the end of the the project so we can take it out and try it out.

At the present time we do not have any home work assignments.

Wednesday, February 17, 2010

This Post is for the week of (2/16/2010 to 2/19/2010)

WOOD SHOP
Students will continue on projects. Grate head way is being made and many projects are be finished.

PLASTICS CLASS
We are working on the group project. We are building a canoe. Students will get to work with Fiberglass. Students are very excited.
At the present time we are assembling the sides to the bottom.

There are no home work assignments at the present time.

Friday, February 5, 2010

This post is for the week of (2/8/2010 to 2/12/2010)

WOOD SHOP
Students will continue on projects. Grate head way is being made and many projects are be finished.

PLASTICS CLASS
We are working on the group project. We are building a canoe. Students will get to work with Fiberglass. Students are very excited.

There are no home work assignments at the present time.

Thursday, February 4, 2010

This post is for the week of (2/1/10 to 2/5)
Wood Students
Many students are nearing completion of their second projects. Some projects are on display in the show case by the Gym. Stop and take a look if you come in for a game.
Students will be starting projects on the wood lathe. Each is responsible for one project on the lathe.
No home work at the present time.

Plastic students
Students are finishing a laminating project this week.
We will be starting a group project this week.
We will be building a canoe in class. It will be built from plywood and Fiberglass.
Students are very excited about the project. When weather is warm we will be testing them.

Friday, January 22, 2010

This post is for the week (1/25/10- 1/29/10)

Wood shop
Students will continue to work on projects. Many students will be finishing up on their projects in the very near future. Students must pay for projects before they are taken home.

Plastics
Students have finished up on the hand mold project We will be starting a group project this week.

At the present time no home work has been assigned.

Friday, January 15, 2010

This post is for the week of (1/18/10 to 1/22/10)
No school Monday

Wood students will be working on projects. Many are nearing completion. I am very happy with the progress many are making.

Plastic students will be finishing up the hand project this week.

Students do not have any home work at the present time.

Monday, January 11, 2010

This post for the week of (1-11-10 to 1-15-10)

Wood shop students will be working on individual projects and we will be reviewing for the up coming mid-terms.

Plastic students will be working on the hand mold project and we will also be reviewing for the up coming mid terms.

Sunday, January 3, 2010

This Posting is for the week of 1/4/10 to 1/8/10

Basic and Advanced Cabinet Making
Students will be working on individual projects and we will be reviewing all information covered up to this point in preparation for up coming Mid terms.

Plastics Technology
We will be continuing with the mold making project and will be pouring with the Water extends polyester resin. We will also start reviewing for upcoming Mid terms.